Avaya Configuring IP, ARP, RIP, and OSPF Services Manual de usuario Pagina 256
- Pagina / 362
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring IP, ARP, RIP, and OSPF Services
A-16
117356-E Rev 00
Parameter: Forward Cache Size
Path: Configuration Manager > Protocols > IP > Interfaces
Default: 128
Options: 64-entry minimum; no maximum
Function: Specifies the maximum number of entries allowed in the forwarding table at
one time.
Instructions: Specify a forwarding table size for each interface. This parameter controls the
number of destinations that are cached in the forwarding table on this receiving
interface. When this interface receives an IP packet, the router looks up the
destination in the forwarding table. Therefore, an interface that receives
packets for a large number of destinations may benefit from a larger
forwarding table. The larger the number of entries, the more likely it is that the
destination will already be in the forwarding table and the faster the route
lookups will be for those destinations. Configuring a forwarding table size that
is larger than necessary reduces the total amount of memory usable by other
applications. Configuring a forwarding table size that is too small can affect
overall router performance. Check the number of cache hits and misses to
determine the optimal size of the forwarding table. For debugging purposes, if
you see the wfIpInterfaceCacheMisses statistic going up at a rapid rate,
consider increasing the table size. However, an occasional cache miss does not
warrant an increase in table size.
MIB Object ID: 1.3.6.1.4.1.18.3.5.3.2.1.4.1.104
Parameter: Enable Security
Path: Configuration Manager > Protocols > IP > Interfaces
Default: Disable
Options: Enable
|
Disable
Function: Specifies whether Revised IP Security Option (RIPSO) is enabled for the
interface.
Instructions: If you do not support RIPSO on your network, accept the default setting,
Disable. If you are configuring RIPSO support, set this parameter to Enable to
access the rest of the RIPSO parameters.
MIB Object ID: 1.3.6.1.4.1.18.3.5.3.2.1.4.1.76
- Configuring IP, ARP, RIP 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117356-E Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 32
- OSPF Neighbors 35
- Neighbor Adjacencies 35
- Designated Routers 36
- OSPF Areas 37
- OSPF Router Types 39
- AS External Routes 39
- OSPF Implementation Notes 40
- Router Discovery Protocol 41
- Route Preferences 41
- Route Weights 42
- Figure 1-6. IP Routing Table 44
- IP Traffic Filters 47
- Chapter 2 49
- Starting IP Services 49
- Starting RIP 51
- Starting OSPF 52
- Starting Router Discovery 52
- Adding RIP to an IP Interface 55
- RIP advertises subnets 61
- Chapter 3 63
- Caution: 80
- Customizing an IP Interface 82
- Configuring an SMDS Address 98
- Using the BCC 101
- Using Site Manager 102
- Deleting IP from an Interface 105
- Defining a Static Route 109
- (continued) 111
- (continued) 112
- Choosing a Broadcast Type 115
- Chapter 4 119
- <state> 120
- Figure 4-1. Proxy ARP Example 125
- Chapter 5 131
- Customizing RIP Services 131
- Defining a RIP Accept Policy 154
- Chapter 6 171
- Customizing OSPF Services 171
- Figure 6-1. OSPF ASE Routes 179
- Specifying the Metric Cost 203
- Appendix A 241
- Site Manager Parameters 241
- IP Parameters 242
- IP Interface Parameters 244
- IP Global Parameters 259
- Static Route Parameters 266
- Adjacent Host Parameters 270
- Router Discovery Parameters 273
- OSPF Parameters 275
- OSPF Interface Parameters 280
- OSPF Area Parameters 289
- Area Range Parameters 293
- OSPF NSSA Range Parameters 296
- RIP Parameters 302
- Appendix B 309
- Routing Policy Parameters 309
- RIP Accept Policy Parameters 313
- OSPF Accept Policy Parameters 314
- Appendix C 331
- RIP Export Filters 335
- OSPF Import Filters 338
- OSPF Export Filters 339
- Appendix D 343
- Route Weight Worksheet 343
- Appendix E 347
- IP/OSPF Configuration Example 347
- Area 0.0.0.1STUB area 0.0.0.2 348
- Backbone 0.0.0.0 348
Relacionado con productos y manuales para Redes Avaya Configuring IP, ARP, RIP, and OSPF Services
Redes Avaya (109351-F Manual de usuario
(136 paginas)
(136 paginas)
Redes Avaya B179 Nota de aplicación
(35 paginas)
(35 paginas)
Redes Avaya BCM200/400 Manual de instalación
(445 paginas)
(445 paginas)
Redes Avaya Call Center Reporting Manual de usuario
(99 paginas)
(99 paginas)
Redes Avaya BCM450 Guía de configuración
(13 paginas)
(13 paginas)
Redes Avaya BayRS Version 13.20 Manual de usuario
(134 paginas)
(134 paginas)
Redes Avaya Event Messages for Routers Manual de usuario
(928 paginas)
(928 paginas)
Redes Avaya Bell Canada SIP Trunking Service with Business Communication Manager 450 Nota de aplicación
(45 paginas)
(45 paginas)
Redes Avaya R2 Guía de instalación
(147 paginas)
(147 paginas)
Redes Avaya BayRS, BCC, and Site Manager Software Version 15.1.0.0 Fixed Anomalies Manual de usuario
(26 paginas)
(26 paginas)
Redes Avaya Configuring ATM Services Manual de usuario
(262 paginas)
(262 paginas)
Redes Avaya BayRs Version 12.20 aviso
(54 paginas)
(54 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales