Avaya Configuring Dial Services Manual de usuario Pagina 132
- Pagina / 428
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring Dial Services
5-4 114062 Rev. B
• A call is designated for the standby circuit.
The router activates a standby circuit only when the remote router calls the
host router over a standby circuit or you activate the circuit manually.
• You activate a standby circuit manually.
Typically, circuits at the remote site will be hot standby circuits, while at the
central site, they will be regular standby circuits. Configuring hot standby circuits
for the remote router means that the remote router monitors the status of its
primary connections, which is easier for the remote router than the central router
because there are fewer connections.
Standby circuits support standard demand circuit features such as multilink,
unnumbered interfaces, dial optimized routing, and outbound filtering.
Guidelines for Configuring Standby Circuits
A standby circuit must be configured at the central site and at the remote site. To
configure a standby circuit, you select a demand circuit then set the Standby Mode
parameter to either Hot Standby or Standby. (Refer to Appendix A for parameter
descriptions.)
When setting up a standby circuit, follow these guidelines:
• Configure one side of the connection to initiate calls (the hot standby circuit).
This is the outgoing side of the connection.
• Configure one side of the connection to receive calls (the standby circuit).
This is the incoming side of the connection.
• If you configure routing protocols on the standby circuit, the Inactivity
Timeout parameter does not work. Once the router brings up the standby
circuit, the routing protocols keep the connection active.
• Configure the Time of Day schedules and the failback timers only on the hot
standby side of the connection.
• Use CHAP or PAP as the authentication protocol for the circuit.
Note: If the standby circuit is part of a bandwidth-on-demand configuration,
the outgoing side should be the monitor router, and the incoming side should
be the non-monitor router.
- Configuring 1
- Dial Services 1
- Bay Networks Software License 3
- Contents 5
- 114062 Rev. B 10
- About This Guide 25
- Before You Begin 26
- Conventions 26
- Acronyms 27
- Bay Networks Customer Service 29
- How to Get Help 29
- For More Information 30
- Chapter 1 31
- Getting Started 31
- Setting Up a Dial Service 33
- 1-4 114062 Rev. B 34
- Configuring Line Pools 35
- Note: On the BLN 38
- Configuring BRI Lines 41
- Configuring PRI Lines 42
- 114062 Rev. B 1-13 43
- 1-14 114062 Rev. B 44
- 114062 Rev. B 1-15 45
- Adding ISDN Lines to a Pool 46
- 114062 Rev. B 1-17 47
- Configuring Circuits 49
- Creating Demand Circuits 49
- 1-20 114062 Rev. B 50
- 114062 Rev. B 1-21 51
- Enabling a Protocol 53
- 1-24 114062 Rev. B 54
- 6. Do one of the following: 54
- Creating Backup Circuits 55
- Specifying the Backup Mode 57
- Creating Bandwidth Circuits 58
- 114062 Rev. B 1-29 59
- Specifying the Bandwidth Mode 60
- 114062 Rev. B 1-31 61
- 1-32 114062 Rev. B 62
- 3. Do one of the following: 62
- 114062 Rev. B 1-33 63
- 1-34 114062 Rev. B 64
- 4. Click on OK 64
- 114062 Rev. B 1-35 65
- 1-36 114062 Rev. B 66
- (Figure 71
- What to Do Next 73
- Chapter 2 75
- Dial Services Overview 75
- 2-2 114062 Rev. B 76
- Table 2-1. Dial Service Names 76
- Dial-on-Demand Service 78
- Demand Lines and Pools 79
- 2-6 114062 Rev. B 80
- Demand Circuit Protocols 81
- 2-8 114062 Rev. B 82
- Activating Demand Circuits 83
- Terminating Demand Circuits 84
- 2-12 114062 Rev. B 86
- Dial Backup Service 87
- 2-14 114062 Rev. B 88
- 114062 Rev. B 2-15 89
- time period 90
- Backup Lines and Pools 91
- 2-18 114062 Rev. B 92
- Activating the Backup Line 93
- 2-20 114062 Rev. B 94
- Bandwidth-on-Demand Service 95
- 2-22 114062 Rev. B 96
- 2-24 114062 Rev. B 98
- Terminating Secondary Lines 99
- Configuring Dial Services 100
- 2-26 114062 Rev. B 100
- Chapter 3 101
- ISDN Overview 101
- ISDN Standards 102
- The D Channel 103
- Primary Rate Interface 103
- 3-4 114062 Rev. B 104
- Figure 3-3. LAPD Frame 104
- ISDN Interfaces 105
- Reference Points 106
- 114062 Rev. B 3-7 107
- 3-8 114062 Rev. B 108
- Chapter 4 109
- Implementation Notes 109
- Types of Authentication 110
- 114062 Rev. B 4-3 111
- 4-4 114062 Rev. B 112
- 114062 Rev. B 4-5 113
- Asynchronous PPP 114
- 114062 Rev. B 4-7 115
- RADIUS Accounting Services 116
- IP Adjacent Hosts 117
- ISDN Services 118
- 114062 Rev. B 4-11 119
- 4-12 114062 Rev. B 120
- 114062 Rev. B 4-13 121
- 4-14 114062 Rev. B 122
- 114062 Rev. B 4-15 123
- Incoming Call Filtering 124
- Rate Adaption 124
- Example 1 125
- Example 2 125
- 4-18 114062 Rev. B 126
- 114062 Rev. B 4-19 127
- 4-20 114062 Rev. B 128
- Chapter 5 129
- 5-2 114062 Rev. B 130
- How Standby Circuits Work 131
- 5-4 114062 Rev. B 132
- 114062 Rev. B 5-5 133
- 5-6 114062 Rev. B 134
- Callback 136
- Configuring Callback 137
- 5-10 114062 Rev. B 138
- Demand Circuit Groups 139
- 5-12 114062 Rev. B 140
- 114062 Rev. B 5-13 141
- 5-14 114062 Rev. B 142
- Static Routes 143
- Dial Optimized Routing 143
- 5-16 114062 Rev. B 144
- 114062 Rev. B 5-17 145
- 5-18 114062 Rev. B 146
- Data Compression 147
- PPP Multilink 148
- Protocol Prioritization 148
- 114062 Rev. B 5-21 149
- Chapter 6 151
- Bandwidth for Backup Circuits 152
- 114062 Rev. B 6-3 153
- 6-4 114062 Rev. B 154
- 114062 Rev. B 6-5 155
- 6-6 114062 Rev. B 156
- Chapter 7 157
- Multilink Fragmentation 159
- 7-4 114062 Rev. B 160
- How BAP Works 161
- Configuring BAP 162
- Chapter 8 165
- Customizing Line Pools 165
- Changing Pool IDs 166
- Deleting Pools 167
- 5. Click on OK 169
- 6. Click on Done 169
- Modifying Modem Configurations 170
- 114062 Rev. B 8-9 173
- 114062 Rev. B 8-11 175
- Modifying ISDN Configurations 176
- Appendix A 177
- Click on OK 177
- Click on Done 177
- Changing PRI Timeslots 179
- 114062 Rev. B 8-17 181
- Modifying the Adaption Rate 183
- 114062 Rev. B 8-21 185
- 114062 Rev. B 8-23 187
- 114062 Rev. B 8-25 189
- 114062 Rev. B 8-27 191
- 114062 Rev. B 8-29 193
- Chapter 9 195
- Customizing Demand Circuits 195
- 114062 Rev. B 9-5 199
- 114062 Rev. B 9-7 201
- 114062 Rev. B 9-9 203
- (continued) 204
- 114062 Rev. B 9-13 207
- 9-14 114062 Rev. B 208
- 7. Click on OK 208
- 114062 Rev. B 9-17 211
- 9-18 114062 Rev. B 212
- 114062 Rev. B 9-21 215
- Removing Demand Circuits 217
- Chapter 10 219
- Customizing Backup Circuits 219
- 10-4 114062 Rev. B 222
- 114062 Rev. B 10-5 223
- 114062 Rev. B 10-7 225
- 10-8 114062 Rev. B 226
- 4. Click on Done 226
- 114062 Rev. B 10-9 227
- 114062 Rev. B 10-11 229
- 114062 Rev. B 10-13 231
- 114062 Rev. B 10-15 233
- 114062 Rev. B 10-17 235
- Chapter 11 237
- 11-4 114062 Rev. B 240
- 2. Click on Options 240
- 114062 Rev. B 11-5 241
- 11-6 114062 Rev. B 242
- 114062 Rev. B 11-7 243
- 11-8 114062 Rev. B 244
- 114062 Rev. B 11-9 245
- 114062 Rev. B 11-11 247
- 114062 Rev. B 11-13 249
- Chapter 12 251
- Customizing Phone Lists 251
- Local Phone Lists 252
- 114062 Rev. B 12-3 253
- Click on Add 254
- 114062 Rev. B 12-7 257
- Enabling PRI Multirate 258
- 114062 Rev. B 12-9 259
- 114062 Rev. B 12-11 261
- Chapter 13 265
- Customizing Caller Resolution 265
- 114062 Rev. B 13-3 267
- 13-4 114062 Rev. B 268
- 9. Click on OK 268
- Dial Service Parameters 271
- A-2 114062 Rev. B 272
- 274
- 275
- 276
- 277
- 280
- 282
- 283
- 286
- 289
- A-20 114062 Rev. B 290
- BRI Configuration Parameters 292
- A-28 114062 Rev. B 298
- 299
- 300
- 302
- 303
- 304
- A-36 114062 Rev. B 306
- A-38 114062 Rev. B 308
- A-40 114062 Rev. B 310
- A-44 114062 Rev. B 314
- 315
- A-46 114062 Rev. B 316
- 317
- A-48 114062 Rev. B 318
- A-50 114062 Rev. B 320
- 325
- 326
- A-58 114062 Rev. B 328
- A-60 114062 Rev. B 330
- 332
- 333
- A-64 114062 Rev. B 334
- A-70 114062 Rev. B 340
- 341
- 341
- 342
- A-74 114062 Rev. B 344
- 345
- A-76 114062 Rev. B 346
- A-78 114062 Rev. B 348
- A-80 114062 Rev. B 350
- A-82 114062 Rev. B 352
- 353
- A-84 114062 Rev. B 354
- Local Phone Number Parameters 355
- A-86 114062 Rev. B 356
- A-88 114062 Rev. B 358
- A-90 114062 Rev. B 360
- A-92 114062 Rev. B 362
- 363
- 364
- A-96 114062 Rev. B 366
- A-98 114062 Rev. B 368
- A-100 114062 Rev. B 370
- A-102 114062 Rev. B 372
- A-104 114062 Rev. B 374
- Appendix B 377
- Configuration Examples 377
- Dial-on-Demand with PPP 378
- B-4 114062 Rev. B 380
- Table B-3. IP Parameters 380
- Configuration Examples 381
- Configuration of Router 1 382
- Configuration of Router 2 383
- B-8 114062 Rev. B 384
- B-10 114062 Rev. B 386
- Table B-14. IP Parameters 386
- B-14 114062 Rev. B 390
- Outgoing Phone List window 391
- B-16 114062 Rev. B 392
- B-20 114062 Rev. B 396
- B-22 114062 Rev. B 398
- Appendix C 401
- C-2 114062 Rev. B 402
- C-4 114062 Rev. B 404
- C-6 114062 Rev. B 406
- C-8 114062 Rev. B 408
- C-10 114062 Rev. B 410
- Appendix D 411
- Ordering PRI Lines 412
- Appendix E 413
- E-2 114062 Rev. B 414
- (continued) 415
- E-4 114062 Rev. B 416
- E-6 114062 Rev. B 418
- 114062 Rev. B Index-1 419
- 114062 Rev. B Index-3 421
- 114062 Rev. B Index-5 423
- 114062 Rev. B Index-7 425
- 114062 Rev. B Index-9 427
Relacionado con productos y manuales para Contestadores automáticos Avaya Configuring Dial Services
Contestadores automáticos Avaya Advanced Paging Productivity Pack BCM Rls 6.0 Manual de usuario
(77 paginas)
(77 paginas)
Contestadores automáticos Avaya 2033 IP Conference Phone - Communication Server 1000 Guía de inicio rápido
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.980 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales