Avaya Business Communications Manager 5.0 - Configuration - System Manual de usuario Pagina 78
- Pagina / 224
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
78 BCM450 MBM and legacy Norstar configuration
Nortel Business Communications Manager 5.0
Configuration — System
NN40170-501 02.04 Standard
September 2009
Copyright © 2009, Nortel Networks
Even if you are not modifying the default configuration, you must click OK to
activate the MBM with the assigned values.
--End--
Attention: You must have sufficient resources to configure MBMs. If
sufficient resources (DNs available on system, consecutive line numbers) do
not exist to configure an MBM, you receive an error message. The MBM and
the entry configuration revert back to Empty/None.
Variable definitions
Configuring legacy Norstar modules
Configure legacy Norstar modules with your FEM to use the functionality of
your legacy Norstar modules. The BCM system suggests default values for
your modules. You can modify this default configuration depending on your
system preference.
To configure legacy Norstar modules through Telset Administration, select
**Config > Hardware > Main unit > MBMs > FEM.
Prerequisites
• A legacy Norstar module must be connected to your BCM system through
a FEM installed in the main unit.
Variable Value
Module type This read-only value is the type of module allocated to this
resource. In this case the value is the type of MBM.
Start DN The lowest DN in the range of DNs assigned to your resource.
The DNs in the range can be consecutive or non-consecutive.
Public received digits/OLI The public received digits/OLI (outgoing line identification) are
the digits that display on the telephone called from this DN over
the public network. This number is usually the same as the DN.
Private received digits/OLI The private received digits/OLI (outgoing line identification) are
the digits that display on the telephone called from this DN over
the private network. This number is usually the same as the DN.
Assign target lines Select this checkbox to assign target lines to your DNs.
Start Line The first line number in the sequence of consecutive lines
assigned to your MBM.
Attention: The variables that appear in the configure dialog box differ depending upon the type of MBM
you choose to configure.
- Configuration — System 1
- Contents 3
- System capacity reference 143 6
- New in this release 7
- 8 New in this release 8
- New in this release 9 9
- 10 New in this release 10
- Introduction 11
- 12 Introduction 12
- Fundamentals 13
- Startup Profile 14
- Scheduled services 15
- Directory numbers 16
- IP trunk module configuration 16
- Fundamentals 17 17
- 18 Fundamentals 18
- SNMP management 19
- Music source and BcmAmp 21
- 22 Fundamentals 22
- System configuration 23
- 24 System configuration 24
- BCM 5.0 system configuration 25
- Accessing the BCM Web page 28
- Connecting to the BCM system 30
- Saving the programming record 34
- Administration 39
- Configuring the IP address 41
- Configuring the modem 41
- Selecting the region 42
- Initializing voice mail 42
- Creating Telset user accounts 43
- Element Manager 45
- Entering the keycode 47
- Configuring IP Phones 54
- Configuring SNMP settings 55
- Deleting an SNMP manager 57
- Creating user accounts 62
- BCM 5.0 internal resources 71
- Configuring IP trunks 72
- Configuring main unit MBMs 77
- ISDN interface management 91
- Disabling an ISDN interface 93
- Deleting an ISDN interface 93
- Connecting an ISDN interface 94
- Modem interface management 97
- Enabling a modem interface 98
- Disabling a modem interface 98
- Deleting a modem interface 99
- Connecting a modem interface 99
- Procedure steps 100
- Variable definitions 102
- WAN Failover on BCM50 103
- CAUTION Router Settings 104
- Assigned is disabled 108
- Prerequisites 110
- NN40170-501 02.04 Standard 112
- September 2009 112
- Guide. (NN40170-502) 114
- BCM 5.0 scheduled services 115
- Configuring scheduled service 117
- Adding music to the play list 126
- Using the BcmAmp Player 128
- Basic configuration testing 129
- BCM 5.0 main unit testing 133
- Testing the main unit 134
- Troubleshooting the main unit 134
- Testing a station MBM 142
- Testing a trunk MBM 143
- System parameters reference 151
- BCM 5.0 startup parameters 152
- Module record 154
- Trunk module parameters 155
- Global, Legacy) 158
- System capacity reference 163
- Navigation 165
- Interface availability 165
- Tones and cadences 168
- Hold, Warble, Intrusion 175
- Reorder, 1 kHz 176
- Analog trunk parameters 196
- Transmission parameters 201
- Call supervision parameters 202
- GASM8 parameters 205
- GASI parameters 208
- ATA2 parameters 210
- ATA2 DR6 211
- ATA2 DR7 212
- Voice mail 214
- ISDN line services 216
- Table 28 ISDN line services 217
- ISDN services by Protocol 217
- Programmable analog interface 219
- Removing a profile 221
Relacionado con productos y manuales para Redes Avaya Business Communications Manager 5.0 - Configuration - System
Redes Avaya ALGO-8028-SM Manual de usuario
(29 paginas)
(29 paginas)
Redes Avaya P332MF Manual de usuario
(182 paginas)
(182 paginas)
Redes Avaya IPTM96-CM601 Manual de usuario
(30 paginas)
(30 paginas)
Redes Avaya 38DHB0002UKDD Manual de usuario
(144 paginas)
(144 paginas)
Redes Avaya G700 Manual de usuario
(768 paginas)
(768 paginas)
Redes Avaya VF 3000 Manual de usuario
(61 paginas)
(61 paginas)
Redes Avaya 106760804 Manual de usuario
(764 paginas)
(764 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales