Avaya Business Communications Manager 5.0 - Configuration - System Manual de usuario Pagina 75
- Pagina / 224
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Nortel Business Communications Manager 5.0
Configuration — System
NN40170-501 02.04 Standard
September 2009
Copyright © 2009, Nortel Networks
BCM450 MBM and legacy Norstar
configuration
The information in this chapter applies only to BCM450 platform running BCM
5.0.
Attention: Legacy Norstar configuration is not supported on BCM50.
This section provides information about configuring and deconfiguring the
media bay modules (MBM) and legacy Norstar modules in your BCM main
unit.
Prerequisites to BCM450 MBM and legacy Norstar configuration
• Launch Business Element Manager and connect to your BCM system. For
more information, see Connecting to the BCM system (page 30).
• For information about configuring internal resources through Telset
Administration, see Telset Administration Guide (NN40170-604).
• You can add a FEM in the main unit only to connect legacy Norstar
modules. A FEM does not function in an expansion unit.
• There must be enough DNs available in the system to populate the entire
MBM being configured, or you cannot configure the MBM and the MBM
does not function.
• There must be enough consecutive line numbers available in the system
to populate the entire MBM, or you cannot configure the MBM and the
MBM configuration does not change.
• The target lines assigned to the DNs are auto-selected by the system and
do not need to be consecutive. The system attempts to find sufficient free
target lines to assign one to each allocated DN.
• Configure the R2MFC MBM as a DTI-PRI MBM with additional
configuration requirements to set the attributes of the PRI protocol such
that the device operates as an R2MFC module.
- Configuration — System 1
- Contents 3
- System capacity reference 143 6
- New in this release 7
- 8 New in this release 8
- New in this release 9 9
- 10 New in this release 10
- Introduction 11
- 12 Introduction 12
- Fundamentals 13
- Startup Profile 14
- Scheduled services 15
- Directory numbers 16
- IP trunk module configuration 16
- Fundamentals 17 17
- 18 Fundamentals 18
- SNMP management 19
- Music source and BcmAmp 21
- 22 Fundamentals 22
- System configuration 23
- 24 System configuration 24
- BCM 5.0 system configuration 25
- Accessing the BCM Web page 28
- Connecting to the BCM system 30
- Saving the programming record 34
- Administration 39
- Configuring the IP address 41
- Configuring the modem 41
- Selecting the region 42
- Initializing voice mail 42
- Creating Telset user accounts 43
- Element Manager 45
- Entering the keycode 47
- Configuring IP Phones 54
- Configuring SNMP settings 55
- Deleting an SNMP manager 57
- Creating user accounts 62
- BCM 5.0 internal resources 71
- Configuring IP trunks 72
- Configuring main unit MBMs 77
- ISDN interface management 91
- Disabling an ISDN interface 93
- Deleting an ISDN interface 93
- Connecting an ISDN interface 94
- Modem interface management 97
- Enabling a modem interface 98
- Disabling a modem interface 98
- Deleting a modem interface 99
- Connecting a modem interface 99
- Procedure steps 100
- Variable definitions 102
- WAN Failover on BCM50 103
- CAUTION Router Settings 104
- Assigned is disabled 108
- Prerequisites 110
- NN40170-501 02.04 Standard 112
- September 2009 112
- Guide. (NN40170-502) 114
- BCM 5.0 scheduled services 115
- Configuring scheduled service 117
- Adding music to the play list 126
- Using the BcmAmp Player 128
- Basic configuration testing 129
- BCM 5.0 main unit testing 133
- Testing the main unit 134
- Troubleshooting the main unit 134
- Testing a station MBM 142
- Testing a trunk MBM 143
- System parameters reference 151
- BCM 5.0 startup parameters 152
- Module record 154
- Trunk module parameters 155
- Global, Legacy) 158
- System capacity reference 163
- Navigation 165
- Interface availability 165
- Tones and cadences 168
- Hold, Warble, Intrusion 175
- Reorder, 1 kHz 176
- Analog trunk parameters 196
- Transmission parameters 201
- Call supervision parameters 202
- GASM8 parameters 205
- GASI parameters 208
- ATA2 parameters 210
- ATA2 DR6 211
- ATA2 DR7 212
- Voice mail 214
- ISDN line services 216
- Table 28 ISDN line services 217
- ISDN services by Protocol 217
- Programmable analog interface 219
- Removing a profile 221
Relacionado con productos y manuales para Redes Avaya Business Communications Manager 5.0 - Configuration - System
Redes Avaya ALGO-8028-SM Manual de usuario
(29 paginas)
(29 paginas)
Redes Avaya P332MF Manual de usuario
(182 paginas)
(182 paginas)
Redes Avaya IPTM96-CM601 Manual de usuario
(30 paginas)
(30 paginas)
Redes Avaya 38DHB0002UKDD Manual de usuario
(144 paginas)
(144 paginas)
Redes Avaya G700 Manual de usuario
(768 paginas)
(768 paginas)
Redes Avaya VF 3000 Manual de usuario
(61 paginas)
(61 paginas)
Redes Avaya 106760804 Manual de usuario
(764 paginas)
(764 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales