Avaya Business Communications Manager 5.0 - Configuration - System Manual de usuario Pagina 156
- Pagina / 224
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
156 System parameters reference
Nortel Business Communications Manager 5.0
Configuration — System
NN40170-501 02.04 Standard
September 2009
Copyright © 2009, Nortel Networks
NSF
Extension
None, WATS, ALL PRI
The Network Specific Facilities (NSF) information element is used to request a particular
service from the network. Settings are based on the type of switch to which the line
connects.
Suggested settings:
DMS-100/250: NONE
Siemens ESWD, Lucent 5ESS: WATS
GTD5, DMS-10: ALL
If you select NONE, the NSF extension bit is not set for any service.
If you select WATS, the NSF extension bit is set for unbanded OUTWATS calls.
If you select ALL, the NSF extension is always set for all CbC services.
Appears only for NI protocol.
Protocol
type
User, Network PRI
If you select SL-1 protocol, an additional setting, Protocol type, appears.
SL-1 protocol is a private networking protocol. Use this protocol to designate a BCM 5.0
node as a Network (controller). The default setting is User (client). In public network
configurations, the CO is generally considered the Network side or controller.
Applies to SL-1 protocol only.
B-channel
selection
sequence
Ascending
Sequential
Descending
Sequential
None
PRI
Defines how B-channel resources are selected for call processing.
Answer
timer
1, 2, 3, 4, or 5 sec. E&
M
PRI
Set the minimum duration of an answer signal before a call is considered to be answered.
Disconnect
timer
60, 100, 260, 460,
or 600
milliseconds
Loo
p
T1
Specify the duration of an Open Switch Interval (OSI) before a call on a supervised
external line is considered disconnected. This setting must match the setting for the line
at the central office (CO).
You must enable disconnect supervision by changing the Line Trunk mode attribute.
Under the Telephony Services sub-heading, choose Lines and Line/trunk Data.
Attribute Value Module/line type
- Configuration — System 1
- Contents 3
- System capacity reference 143 6
- New in this release 7
- 8 New in this release 8
- New in this release 9 9
- 10 New in this release 10
- Introduction 11
- 12 Introduction 12
- Fundamentals 13
- Startup Profile 14
- Scheduled services 15
- Directory numbers 16
- IP trunk module configuration 16
- Fundamentals 17 17
- 18 Fundamentals 18
- SNMP management 19
- Music source and BcmAmp 21
- 22 Fundamentals 22
- System configuration 23
- 24 System configuration 24
- BCM 5.0 system configuration 25
- Accessing the BCM Web page 28
- Connecting to the BCM system 30
- Saving the programming record 34
- Administration 39
- Configuring the IP address 41
- Configuring the modem 41
- Selecting the region 42
- Initializing voice mail 42
- Creating Telset user accounts 43
- Element Manager 45
- Entering the keycode 47
- Configuring IP Phones 54
- Configuring SNMP settings 55
- Deleting an SNMP manager 57
- Creating user accounts 62
- BCM 5.0 internal resources 71
- Configuring IP trunks 72
- Configuring main unit MBMs 77
- ISDN interface management 91
- Disabling an ISDN interface 93
- Deleting an ISDN interface 93
- Connecting an ISDN interface 94
- Modem interface management 97
- Enabling a modem interface 98
- Disabling a modem interface 98
- Deleting a modem interface 99
- Connecting a modem interface 99
- Procedure steps 100
- Variable definitions 102
- WAN Failover on BCM50 103
- CAUTION Router Settings 104
- Assigned is disabled 108
- Prerequisites 110
- NN40170-501 02.04 Standard 112
- September 2009 112
- Guide. (NN40170-502) 114
- BCM 5.0 scheduled services 115
- Configuring scheduled service 117
- Adding music to the play list 126
- Using the BcmAmp Player 128
- Basic configuration testing 129
- BCM 5.0 main unit testing 133
- Testing the main unit 134
- Troubleshooting the main unit 134
- Testing a station MBM 142
- Testing a trunk MBM 143
- System parameters reference 151
- BCM 5.0 startup parameters 152
- Module record 154
- Trunk module parameters 155
- Global, Legacy) 158
- System capacity reference 163
- Navigation 165
- Interface availability 165
- Tones and cadences 168
- Hold, Warble, Intrusion 175
- Reorder, 1 kHz 176
- Analog trunk parameters 196
- Transmission parameters 201
- Call supervision parameters 202
- GASM8 parameters 205
- GASI parameters 208
- ATA2 parameters 210
- ATA2 DR6 211
- ATA2 DR7 212
- Voice mail 214
- ISDN line services 216
- Table 28 ISDN line services 217
- ISDN services by Protocol 217
- Programmable analog interface 219
- Removing a profile 221
Relacionado con productos y manuales para Redes Avaya Business Communications Manager 5.0 - Configuration - System
Redes Avaya ALGO-8028-SM Manual de usuario
(29 paginas)
(29 paginas)
Redes Avaya P332MF Manual de usuario
(182 paginas)
(182 paginas)
Redes Avaya IPTM96-CM601 Manual de usuario
(30 paginas)
(30 paginas)
Redes Avaya 38DHB0002UKDD Manual de usuario
(144 paginas)
(144 paginas)
Redes Avaya G700 Manual de usuario
(768 paginas)
(768 paginas)
Redes Avaya VF 3000 Manual de usuario
(61 paginas)
(61 paginas)
Redes Avaya 106760804 Manual de usuario
(764 paginas)
(764 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales