Avaya Business Communications Manager 5.0 - Configuration - System Manual de usuario Pagina 110
- Pagina / 224
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
110 Dial-up resources configuration
Nortel Business Communications Manager 5.0
Configuration — System
NN40170-501 02.04 Standard
September 2009
Copyright © 2009, Nortel Networks
Variable definitions
Automatic dial-out interface configuration
Use the following procedure to create an automatic dial-out interface.
Management applications such as SNMP trap dial out, Scheduled Log
transfer, Scheduled Backup, and Scheduled CDR records transfer can use
automatic dial-out over an ISDN or Modem interface. To configure the
automatic data transfer, the administrator must configure a static route with
the auto dial-out field selected, and associate it with the application. When
data is sent to the destination address, the network recognizes the address of
the application, and triggers the dial-out to establish the connection.The
packets are then sent over the link to the destination.
Prerequisites
• The dial-out interface must be enabled to configure static routes.
• The disconnect time for the interface must be greater than 60 seconds.
This is configured on the Link Parameters tab of the selected interface
under Configuration > Resources > Dial Up Interfaces.
• Auto dial-out routes cannot be added if the interface is already manually
connected, unless the interface is already connected with auto dial-out
routes configured.
• If an interface is enabled and configured for manual dial-out, the interface
must be disabled before it can be configured for automatic dial-out.
Variable Description
Local IP Address Specification
Remote assigned When selected, the BCM obtains its IP address from the remote
end.
Default: selected
IP address When the Remote Assigned parameter is disabled, a static IP
address must be configured in this parameter.
Remote IP Address Specification
Assign an IP address
to remote
When selected, BCM will assign the IP address in the “IP Address” field of this
section to the remote end of the
connection.
Default: cleared
IP address
The local IP address used on the BCM for the dial-out
connection.
Default: 10.11.16.1
- Configuration — System 1
- Contents 3
- System capacity reference 143 6
- New in this release 7
- 8 New in this release 8
- New in this release 9 9
- 10 New in this release 10
- Introduction 11
- 12 Introduction 12
- Fundamentals 13
- Startup Profile 14
- Scheduled services 15
- Directory numbers 16
- IP trunk module configuration 16
- Fundamentals 17 17
- 18 Fundamentals 18
- SNMP management 19
- Music source and BcmAmp 21
- 22 Fundamentals 22
- System configuration 23
- 24 System configuration 24
- BCM 5.0 system configuration 25
- Accessing the BCM Web page 28
- Connecting to the BCM system 30
- Saving the programming record 34
- Administration 39
- Configuring the IP address 41
- Configuring the modem 41
- Selecting the region 42
- Initializing voice mail 42
- Creating Telset user accounts 43
- Element Manager 45
- Entering the keycode 47
- Configuring IP Phones 54
- Configuring SNMP settings 55
- Deleting an SNMP manager 57
- Creating user accounts 62
- BCM 5.0 internal resources 71
- Configuring IP trunks 72
- Configuring main unit MBMs 77
- ISDN interface management 91
- Disabling an ISDN interface 93
- Deleting an ISDN interface 93
- Connecting an ISDN interface 94
- Modem interface management 97
- Enabling a modem interface 98
- Disabling a modem interface 98
- Deleting a modem interface 99
- Connecting a modem interface 99
- Procedure steps 100
- Variable definitions 102
- WAN Failover on BCM50 103
- CAUTION Router Settings 104
- Assigned is disabled 108
- Prerequisites 110
- NN40170-501 02.04 Standard 112
- September 2009 112
- Guide. (NN40170-502) 114
- BCM 5.0 scheduled services 115
- Configuring scheduled service 117
- Adding music to the play list 126
- Using the BcmAmp Player 128
- Basic configuration testing 129
- BCM 5.0 main unit testing 133
- Testing the main unit 134
- Troubleshooting the main unit 134
- Testing a station MBM 142
- Testing a trunk MBM 143
- System parameters reference 151
- BCM 5.0 startup parameters 152
- Module record 154
- Trunk module parameters 155
- Global, Legacy) 158
- System capacity reference 163
- Navigation 165
- Interface availability 165
- Tones and cadences 168
- Hold, Warble, Intrusion 175
- Reorder, 1 kHz 176
- Analog trunk parameters 196
- Transmission parameters 201
- Call supervision parameters 202
- GASM8 parameters 205
- GASI parameters 208
- ATA2 parameters 210
- ATA2 DR6 211
- ATA2 DR7 212
- Voice mail 214
- ISDN line services 216
- Table 28 ISDN line services 217
- ISDN services by Protocol 217
- Programmable analog interface 219
- Removing a profile 221
Relacionado con productos y manuales para Redes Avaya Business Communications Manager 5.0 - Configuration - System
Redes Avaya ALGO-8028-SM Manual de usuario
(29 paginas)
(29 paginas)
Redes Avaya P332MF Manual de usuario
(182 paginas)
(182 paginas)
Redes Avaya IPTM96-CM601 Manual de usuario
(30 paginas)
(30 paginas)
Redes Avaya 38DHB0002UKDD Manual de usuario
(144 paginas)
(144 paginas)
Redes Avaya G700 Manual de usuario
(768 paginas)
(768 paginas)
Redes Avaya VF 3000 Manual de usuario
(61 paginas)
(61 paginas)
Redes Avaya 106760804 Manual de usuario
(764 paginas)
(764 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.398 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales