Avaya Business Policy Switch 2000 Command Line Interface Release 2.0 Manual de usuario Pagina 87
- Pagina / 233
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 General CLI commands 85
Reference for the Business Policy Switch 2000 Command Line Interface
Upgrading software images
You follow a different procedure depending if you are using a Pure BPS 2000
stack or a Hybrid stack.
The stacking software compatibility requirements are as follows:
• Pure BPS 2000 stack—All units must be running the same software version.
• Pure BayStack 450 stack—All units must be running the same software
version.
• Hybrid stack:
— All BPS 2000 units must be running the same software version.
— All BayStack 410 units must be running the same software version.
— All BayStack 450 units must be running the same software version.
— All software versions must have the identical ISVN.
This section discusses the following topics:
• “Upgrading software in a Pure BPS 2000 stack,” next
• “Upgrading software in a Hybrid stack” on page 86
Upgrading software in a Pure BPS 2000 stack
To download, or upgrade, software in a Pure BPS 2000 stack:
1 Enter
download [address <ip>] image bps2000.img.
3 The switch programs the new
software image into the flash
memory.
100 Mb/s port status LEDs (ports 1 to 8 only): The LEDs begin to
turn on in succession beginning with port 1, which indicates that the
new software image is being programmed into the switch’s flash
memory. When LEDs 1 to 8 are all on, the new software image has
been programmed successfully into the switch’s flash memory.
4 The switch resets automatically. After the reset completes, the new software image initiates the
switch self-test, which comprises various diagnostic routines and
subtests.
The LEDs display various patterns to indicate that the subtests are in
progress.
Table 30 LED Indications during the software download process (continued)
Phase Description LED Indications
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 2.0 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- USA requirements only 3
- European requirements only 3
- Taiwan requirements 4
- Canada requirements only 4
- Contents 7
- Chapter 3 11
- Chapter 4 11
- Chapter 5 12
- Chapter 6 13
- Appendix A 14
- About this guide 21
- Before you begin 21
- Text conventions 22
- Related publications 23
- How to get help 24
- Preface 25 25
- 26 Preface 26
- Chapter 1 27
- CLI Basics 27
- Stacking compatibility 28
- Chapter 1 CLI Basics 27 29
- New features 30
- CLI command modes 31
- 30 Chapter 1 CLI Basics 32
- Port numbering 34
- IP notation 36
- Accessing the CLI 37
- 36 Chapter 1 CLI Basics 38
- Figure 2 BPS 2000 banner 38
- Setting the CLI password 40
- Getting help 41
- Basic navigation 41
- General navigation commands 42
- Keystroke navigation 43
- Parameters 47
- BPS2000#show stack-info 51
- Chapter 1 CLI Basics 51 53
- BPS2000#show stack-oper-mode 56
- Chapter 1 CLI Basics 55 57
- 56 Chapter 1 CLI Basics 58
- Chapter 2 59
- General CLI commands 59
- Setting the terminal 60
- Configuration Filename: 65
- Setting Telnet access 73
- Setting boot parameters 77
- Setting TFTP parameters 81
- Upgrading software 84
- Observing LED indications 86
- Upgrading software images 87
- Displaying interfaces 90
- Setting SNMP parameters 92
- Setting the system event log 97
- Displaying port statistics 100
- Enabling or disabling a port 102
- Naming ports 104
- Setting port speed 105
- Enabling Autopology 109
- Enabling flow control 111
- Enabling rate-limiting 113
- Security 117
- Using MAC address security 122
- Index Mac Address 124
- _____ _________________ 124
- 1 00-60-AF-00-12-30 124
- command is: 125
- Using EAPOL-based security 130
- Using RADIUS authentication 133
- 134 Chapter 3 Security 136
- 212160-B 136
- Using MLT 150
- Using port-mirroring 153
- VLANs and IGMP 157
- 156 Chapter 5 VLANs and IGMP 158
- Parameters and 159
- Description 159
- Using IGMP snooping 172
- Displaying QoS parameters 176
- IP Filter Sets 181
- Resetting 187
- Configuring COPS 188
- Configuring QoS actions 206
- Configuring QoS meters 207
- Configuring QoS shapers 208
- Gathering QoS statistics 210
- Configuring QoS policies 211
- Reordering packets 213
- Command List 215
- 214 Appendix A Command List 216
- Appendix A Command List 215 217
- 216 Appendix A Command List 218
- Appendix A Command List 217 219
- 218 Appendix A Command List 220
- Appendix A Command List 219 221
- 220 Appendix A Command List 222
- Appendix A Command List 221 223
- 222 Appendix A Command List 224
- Appendix A Command List 223 225
- 224 Appendix A Command List 226
Relacionado con productos y manuales para Los conmutadores de red Avaya Business Policy Switch 2000 Command Line Interface Release 2.0
(31 paginas)
(13 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales