Avaya Business Policy Switch 2000 Command Line Interface Release 2.0 Manual de usuario Pagina 212
- Pagina / 233
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
210 Chapter 6 Policy-enabled networks and QoS
212160-B
filter-set <setid> Enter the filter set ID associated with this policy; range is 1 to 65535.
filter-set-name <setname> Enter the name of the filter set associated with this policy.
in-profile-action <actid> Enter the action ID for in-profile traffic; range is 1 to 65535.
in-profile-action-name
<actname>
Enter the action name for in-profile traffic; maximum is 16 alphanumeric
characters.
meter <metid> Enter meter ID associated with this policy; range is 1 to 65535.
meter-name <metname> Enter the meter name associated with this policy; maximum of 16
alphanumeric characters.
in-profile-action <actid> Enter the action ID for in-profile traffic; range is 1 to 65535.
in-profile-action-name
<actname>
Enter the action name for in-profile traffic; maximum is 16 alphanumeric
characters.
out-profile-action <actid> Enter the action ID for out-of-profile traffic; range is 1 to 65535.
out-profile-action-name
<actname>
Enter the action name for in-profile traffic; maximum is 16 alphanumeric
characters.
shaper <shapeid> Enter shaper ID associated with this policy; range is 1 to 65535.
shaper-name
<shapername>
Enter the shaper name associated with this policy; maximum of 16
alphanumeric characters.
shaper-group
<shapegroup>
Enter shaper group ID associated with this policy; range is 2 to 63.
track-statistics
{enable|disable}
Enables maintaining policing statistics on the specified flow. Default is
based on value of setting of
qosagent police-statistics
command.
order <order> Specifies the evaluation order of this policy in relation to other policies
associated with the same interface group. Enter order number; range is 1 to
65535.
Note: Policies with a lower order value are evaluated before policies with a
higher order number. Evaluation goes from lowest value to highest.
delete Deletes the specified QoS policy.
enable|disable Enables or disables the specified QoS policy.
You must define all components associated with a policy, including the
interface group, filter set, meter, and shaper before referencing those
components with a policy.
Table 124 qos policy command parameters and variables (continued)
Parameters and variables Description
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 2.0 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- USA requirements only 3
- European requirements only 3
- Taiwan requirements 4
- Canada requirements only 4
- Contents 7
- Chapter 3 11
- Chapter 4 11
- Chapter 5 12
- Chapter 6 13
- Appendix A 14
- About this guide 21
- Before you begin 21
- Text conventions 22
- Related publications 23
- How to get help 24
- Preface 25 25
- 26 Preface 26
- Chapter 1 27
- CLI Basics 27
- Stacking compatibility 28
- Chapter 1 CLI Basics 27 29
- New features 30
- CLI command modes 31
- 30 Chapter 1 CLI Basics 32
- Port numbering 34
- IP notation 36
- Accessing the CLI 37
- 36 Chapter 1 CLI Basics 38
- Figure 2 BPS 2000 banner 38
- Setting the CLI password 40
- Getting help 41
- Basic navigation 41
- General navigation commands 42
- Keystroke navigation 43
- Parameters 47
- BPS2000#show stack-info 51
- Chapter 1 CLI Basics 51 53
- BPS2000#show stack-oper-mode 56
- Chapter 1 CLI Basics 55 57
- 56 Chapter 1 CLI Basics 58
- Chapter 2 59
- General CLI commands 59
- Setting the terminal 60
- Configuration Filename: 65
- Setting Telnet access 73
- Setting boot parameters 77
- Setting TFTP parameters 81
- Upgrading software 84
- Observing LED indications 86
- Upgrading software images 87
- Displaying interfaces 90
- Setting SNMP parameters 92
- Setting the system event log 97
- Displaying port statistics 100
- Enabling or disabling a port 102
- Naming ports 104
- Setting port speed 105
- Enabling Autopology 109
- Enabling flow control 111
- Enabling rate-limiting 113
- Security 117
- Using MAC address security 122
- Index Mac Address 124
- _____ _________________ 124
- 1 00-60-AF-00-12-30 124
- command is: 125
- Using EAPOL-based security 130
- Using RADIUS authentication 133
- 134 Chapter 3 Security 136
- 212160-B 136
- Using MLT 150
- Using port-mirroring 153
- VLANs and IGMP 157
- 156 Chapter 5 VLANs and IGMP 158
- Parameters and 159
- Description 159
- Using IGMP snooping 172
- Displaying QoS parameters 176
- IP Filter Sets 181
- Resetting 187
- Configuring COPS 188
- Configuring QoS actions 206
- Configuring QoS meters 207
- Configuring QoS shapers 208
- Gathering QoS statistics 210
- Configuring QoS policies 211
- Reordering packets 213
- Command List 215
- 214 Appendix A Command List 216
- Appendix A Command List 215 217
- 216 Appendix A Command List 218
- Appendix A Command List 217 219
- 218 Appendix A Command List 220
- Appendix A Command List 219 221
- 220 Appendix A Command List 222
- Appendix A Command List 221 223
- 222 Appendix A Command List 224
- Appendix A Command List 223 225
- 224 Appendix A Command List 226
Relacionado con productos y manuales para Los conmutadores de red Avaya Business Policy Switch 2000 Command Line Interface Release 2.0
(31 paginas)
(13 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.243 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales