Avaya Business Policy Switch 2000 Command Line Interface Release 2.0 Manual de usuario Pagina 125
- Pagina / 233
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3 Security 123
Reference for the Business Policy Switch 2000 Command Line Interface
mac-security mac-address-table address command
The mac-security mac-address-table address command assigns either
a specific port or a security list to the MAC address. This removes any previous
assignment to the specified MAC address and creates an entry in the BaySecure
table of allowed MAC addresses. The syntax for the
mac-security
mac-address-table address
command is:
mac-security mac-address-table address <H.H.H.> {port
<portlist>|security-list <1-32>}
Table 62 mac-security command parameters and values
Parameters and variables Description
disable|enable Disables or enables MAC address-based security.
filtering {enable|disable} Enables or disables destination address (DA) filtering on intrusion
detected.
intrusion-detect
{enable|disable|forever}
Specifies partitioning of a port when an intrusion is detected:
• enable—port is partitioned for a period of time
• disabled—port is not partitioned on detection
• forever—port is partitioned until manually changed
intrusion-timer <1-65535> Specifies, in seconds, length of time a port is partitioned when an
intrusion is detected; enter the number of you want.
learning-ports <portlist> Specifies MAC address learning. Learned addresses are added
to the table of allowed MAC addresses. Enter the ports you want
to learn; it can be a single port, a range of ports, several ranges,
all, or none.
learning {enable|disable} Specifies MAC address learning:
• enable—enables learning by ports
• disable—disables learning by ports
snmp-lock {enable|disable} Enables or disables a lock on SNMP write-access to the
BaySecure MIBs.
snmp-trap {enable|disable} Enables or disables trap generation upon intrusion detection.
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 2.0 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- USA requirements only 3
- European requirements only 3
- Taiwan requirements 4
- Canada requirements only 4
- Contents 7
- Chapter 3 11
- Chapter 4 11
- Chapter 5 12
- Chapter 6 13
- Appendix A 14
- About this guide 21
- Before you begin 21
- Text conventions 22
- Related publications 23
- How to get help 24
- Preface 25 25
- 26 Preface 26
- Chapter 1 27
- CLI Basics 27
- Stacking compatibility 28
- Chapter 1 CLI Basics 27 29
- New features 30
- CLI command modes 31
- 30 Chapter 1 CLI Basics 32
- Port numbering 34
- IP notation 36
- Accessing the CLI 37
- 36 Chapter 1 CLI Basics 38
- Figure 2 BPS 2000 banner 38
- Setting the CLI password 40
- Getting help 41
- Basic navigation 41
- General navigation commands 42
- Keystroke navigation 43
- Parameters 47
- BPS2000#show stack-info 51
- Chapter 1 CLI Basics 51 53
- BPS2000#show stack-oper-mode 56
- Chapter 1 CLI Basics 55 57
- 56 Chapter 1 CLI Basics 58
- Chapter 2 59
- General CLI commands 59
- Setting the terminal 60
- Configuration Filename: 65
- Setting Telnet access 73
- Setting boot parameters 77
- Setting TFTP parameters 81
- Upgrading software 84
- Observing LED indications 86
- Upgrading software images 87
- Displaying interfaces 90
- Setting SNMP parameters 92
- Setting the system event log 97
- Displaying port statistics 100
- Enabling or disabling a port 102
- Naming ports 104
- Setting port speed 105
- Enabling Autopology 109
- Enabling flow control 111
- Enabling rate-limiting 113
- Security 117
- Using MAC address security 122
- Index Mac Address 124
- _____ _________________ 124
- 1 00-60-AF-00-12-30 124
- command is: 125
- Using EAPOL-based security 130
- Using RADIUS authentication 133
- 134 Chapter 3 Security 136
- 212160-B 136
- Using MLT 150
- Using port-mirroring 153
- VLANs and IGMP 157
- 156 Chapter 5 VLANs and IGMP 158
- Parameters and 159
- Description 159
- Using IGMP snooping 172
- Displaying QoS parameters 176
- IP Filter Sets 181
- Resetting 187
- Configuring COPS 188
- Configuring QoS actions 206
- Configuring QoS meters 207
- Configuring QoS shapers 208
- Gathering QoS statistics 210
- Configuring QoS policies 211
- Reordering packets 213
- Command List 215
- 214 Appendix A Command List 216
- Appendix A Command List 215 217
- 216 Appendix A Command List 218
- Appendix A Command List 217 219
- 218 Appendix A Command List 220
- Appendix A Command List 219 221
- 220 Appendix A Command List 222
- Appendix A Command List 221 223
- 222 Appendix A Command List 224
- Appendix A Command List 223 225
- 224 Appendix A Command List 226
Relacionado con productos y manuales para Los conmutadores de red Avaya Business Policy Switch 2000 Command Line Interface Release 2.0
(31 paginas)
(13 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales