Avaya Configuring Frame Relay Services Manual de usuario Pagina 191
- Pagina / 240
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Site Manager Parameters
117376-C Rev. 00
A-45
Parameter: X.213 Data Priority
Path: Configuration Manager > Protocols > Frame Relay > Services > SVCs
Default: 15
Options: 0 to 15
Function: Sets the priority of data on the network connection as defined in ITU-T Q.933
and X.213. This is a value the router requests; it is not guaranteed. A value of 0
is the lowest priority, with 14 as the highest. A value of 15 means unspecified.
Instructions: If your network supports X.213 prioritization, you should assign a value. You
should accept the default if the network does not support X.213 prioritization,
unless the network is able to accept pieces of signaling information that it does
not recognize.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.9.10.1.14
Parameter: X.213 Data LQA Priority
Path: Configuration Manager > Protocols > Frame Relay > Services > SVCs
Default: 15
Options: 0 to 15
Function: Sets the lowest acceptable priority of data on a connection. A value of 0 is the
lowest priority, with 14 as the highest. A value of 15 means unspecified.
Instructions: If your network supports X.213 prioritization, you should assign a value. You
should accept the default if the network does not support X.213 prioritization,
unless the network is able to accept pieces of signaling information that it does
not recognize.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.9.10.1.15
- Configuring 1
- Frame Relay Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117376-C Rev. 00 10
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 26
- Configuring an SVC 27
- Chapter 2 31
- Frame Relay Overview 31
- Introduction to Frame Relay 32
- Permanent Virtual Circuits 33
- Switched Virtual Circuits 33
- PVC and SVC Comparison 34
- Frame Relay Packets 35
- . Note, however 36
- Management Protocols 37
- BYS0037A 38
- LAPF Operational States 39
- SVC Signaling 41
- Call Setup 42
- Message Processing 43
- Frame Relay Service Records 44
- Frame Relay Access Modes 45
- Direct Access Mode 46
- Hybrid Access Mode 46
- Source Routing 48
- RFC 1490 48
- Address Resolution for PVCs 48
- Address Resolution for SVCs 49
- Traffic Control 50
- Data Compression 51
- Data Encryption 51
- Protocol Prioritization 51
- Traffic Shaping 53
- Quality of Service 55
- Traffic Shaping for SVCs 57
- Incoming 59
- Outgoing 59
- CIR Configuration Guidelines 60
- WCP and CIR Enforcement 60
- Oversubscribing the Interface 62
- X.213 Priority for SVCs 64
- Inactivity Timing for SVCs 64
- Multiline for PVCs 65
- PVC Pass-Through 67
- Frame Relay Dial Services 68
- Caution: 71
- Selecting a Management Type 72
- Selecting a DLCI Address Type 74
- Selecting Address Length 74
- Monitoring the Connection 76
- Polling Interval 77
- Full Enquiry Interval 77
- Customizing PVCs 81
- To delete PVCs: 87
- To move PVCs: 87
- Enabling Multicast 88
- Configuring PVC Pass-Through 90
- <integer> 100
- Enabling Compression for PVCs 102
- Using the BCC 103
- Using Site Manager 103
- Customizing SVCs 105
- For example: 107
- To delete service records: 107
- Call Screening and Blocking 108
- Disabling SVCs 112
- Disconnecting Active SVCs 114
- Setup Timer 121
- <value> 126
- (continued) 128
- Congestion Control 129
- Congestion Timer 130
- Congestion Counter 130
- Congestion Method 131
- To enable congestion control 134
- To enable traffic shaping 139
- To disable compression: 141
- To set X.213 priority value 143
- Deleting Frame Relay 144
- Customizing Frame Relay 145
- Appendix A 147
- Site Manager Parameters 147
- Figure A-2 148
- SVC LAPF Parameters 157
- SVC Signaling Parameters 163
- Parameters for PVCs 168
- PVC Service Record Parameters 172
- SVC Service Record Parameters 180
- SVC Options Parameters 186
- WHERE DOES THIS PARAMETER GO? 200
- Appendix B 201
- Table B-1. RIP Parameters 202
- Appendix C 209
- Monitoring Frame Relay Using 209
- BCC show Commands 209
- Commands for Frame Relay 210
- <option> 212
- <dlci> 215
- <name> 215
- ] [-service 216
- <multiline_name> 223
- <name> 228
Relacionado con productos y manuales para Redes Avaya Configuring Frame Relay Services
Redes Avaya BCM 2.5 Guía de usuario
(50 paginas)
(50 paginas)
Redes Avaya Glossary of Media Processing Server Series Terminology (Software Release 2.1) Manual de usuario
(124 paginas)
(124 paginas)
Redes Avaya BayRS Version 15.2.0.0 aviso
(68 paginas)
(68 paginas)
Redes Avaya Configuring DLSw Services Manual de usuario
(204 paginas)
(204 paginas)
Redes Avaya BCM200/400 Manual de instalación
(386 paginas)
(386 paginas)
Redes Avaya X.25 Manual de usuario
(198 paginas)
(198 paginas)
Redes Avaya Configuring OSI Services Manual de usuario
(148 paginas)
(148 paginas)
Redes Avaya BCM450 Guía de configuración
(11 paginas)
(11 paginas)
Redes Avaya X.25 Manual de usuario
(50 paginas)
(50 paginas)
Redes Avaya BayRS Version 15.1.0.0 aviso
(72 paginas)
(72 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales