Avaya Connecting BayStack AN and ANH Platforms to a Network Manual de usuario Pagina 32
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Connecting BayStack AN and ANH Systems to a Network
1-10
Obtaining the IP Address Manually (Netboot and Directed Netboot)
For Netboot and Directed Netboot, you configure the IP address manually.
Cha
pter 4 describes how to use Site Manager to configure Netboot interfaces.
Cha
pter 5 describes how to configure the netboot interfaces using the Technician
Interface.
Obtaining the IP Address Automatically (EZ-Install)
During the EZ-Install process, the router obtains its address automatically, as
described below.
1. When you power on the AN/ANH, it runs a set of diagnostic tests.
2. The AN/ANH sends a BOOTP request to the upstream router for an IP
address and subnet mask.
The AN/ANH issues the request through all synchronous ports at about the
same time, even if cables are not connected to these ports. Each port
successively tries the following protocols until it receives a response:
• Bay Networks Standard PPP using HDLC (high-level datalink control)
encapsulation
• Frame Relay Annex D
• Frame Relay Local Management Interface (LMI)
• Frame Relay Annex A
The AN/ANH makes two attempts for each protocol. If it does not receive a
response in approximately 4 minutes, the AN/ANH boots the default image
and configuration file in its local file system, as described in the next section,
“Local Boot
.”
3. The first interface on the upstream router to receive the BOOTP request
responds.
4. The upstream router calculates the IP address of the AN/ANH’s synchronous
interface.
How the upstream router calculates the IP address depends on its protocol
configuration. See Step a if the upstream router circuit is running Bay
Networks Standard or is a Frame Relay permanent virtual circuit (PVC) in
direct access mode. See Step b if it is a Frame Relay PVC in group access
mode.
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- About This Guide 15
- Before You Begin 16
- CompuServe 17
- InfoFACTS 18
- World Wide Web 18
- How to Get Help 19
- Conventions 19
- Acronyms 20
- Chapter 1 23
- (continued) 24
- ANH Models 25
- Access Node Software 27
- Router Software 28
- Boot Configuration Options 28
- EZ-Install 29
- The Boot Process 31
- Local Boot 37
- Chapter 2 39
- Booting the Router Routinely 41
- Directed Netboot 42
- Recommendations 43
- Completing a Startup Option 44
- Chapter 3 49
- Setting Up a UNIX Boot Server 49
- Setting Up BOOTP Sockets 50
- Setting Up BOOTPD to Run 51
- Editing the bootptab File 52
- Setting Up a TFTP Server 56
- Editing the inetd.conf File 59
- Verifying the Routes 59
- Rebooting 59
- What to Do Next 60
- Chapter 4 61
- Configuring Network Booting 61
- Creating Configuration Files 62
- Preparing an Image 63
- Configuring Network Booting 67
- 2. Click on Add 68
- 4. Click on OK 69
- 71
- 72
- Enabling Router Interfaces 74
- ??? appears 78
- 1. Click on Client I/F 79
- Chapter 5 83
- Network Boot Client 83
- 84
- 84
- <next 86
- <interface> 86
- Ethernet interface 87
- <interface> 88
- Chapter 6 91
- 93
- About the N11 DCM 97
- The RMON Groups 98
- Ethernet Statistics Group 99
- HostTopN Group 100
- Matrix Group 100
- Filter Group 100
- Packet Capture Group 100
- Enabling the DCM 101
- 103
- 104
- 104
- 105
- 105
- 106
- Disabling DCM 108
- Booting DCM 108
- 2. Click on OK 111
- RMON Implementation Notes 113
- RMON Interoperability Issues 113
- RMON Memory Use 114
- Statistics Group 115
- History Group 115
- Host Group 116
- Filter and Capture Groups 118
- Appendix A 121
- Router Fails to Netboot 123
- <connector> 127
- Displaying Parameter Settings 130
- Debugging the BOOTP Server 131
- Table A-1. BOOTP Messages 132
- <IP_address> 133
- Quick Get Instructions 134
- Upgrading the Software Image 135
- Restoring a Local File System 136
- Appendix B 137
- Global Information Worksheet 139
- Router Protocol Worksheets 141
- OSPF Worksheet 142
- Wide-Area Protocol Worksheets 144
- Frame Relay Worksheet 145
- PPP Standard Worksheet 146
- Appendix C 151
- Implementation Notes 151
- 1: as the volume name 152
- Network Configuration Options 153
- Configuring a Single ANH 154
- Access Node Hub 155
- Configuring Multiple Hubs 156
- Configuring an AUI Port 157
Relacionado con productos y manuales para Software Avaya Connecting BayStack AN and ANH Platforms to a Network
Software Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Manual de usuario
(190 paginas)
(190 paginas)
Software Avaya R4.3 Manual de usuario
(368 paginas)
(368 paginas)
Software Avaya Read Me First: Router Software 11.02 and Site Manager 5.02 Manual de usuario
(10 paginas)
(10 paginas)
Software Avaya Attendant Console Guía de usuario
(96 paginas)
(96 paginas)
Software Avaya B5800 Manual de usuario
(70 paginas)
(70 paginas)
Software Avaya BCM 5.0 - Contact Center - Intelligent Contact Center Manual de usuario
(258 paginas)
(258 paginas)
Software Avaya BCM-IVR 2.1 Guía de usuario
(103 paginas)
(103 paginas)
Software Avaya Bay Command Console Manual de usuario
(130 paginas)
(130 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales