Avaya Connecting BayStack AN and ANH Platforms to a Network Manual de usuario Pagina 126
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Connecting BayStack AN and ANH Systems to a Network
A-6
3.
Check that you have TFTP on the router. To determine this, display the
router’s
loadmap screen message.
If tftp.exe is missing, load it onto the router.
4. Use Site Manager to make sure that IP is enabled and TFTP is created in
the AN/ANH’s configuration file.
Refer to “Verifying the BOOTP Server Setup” later in this appendix.
5. Use Technician Interface commands to verify or correct the status of the
synchronous or Ethernet connectors used for network booting.
Refer to Using Technician Interface Software for instructions. Following are
some examples of AN/ANH commands and their responses, as well as some
connector and interface settings you should consider:
• Enter the following command to display the router driver:
get wfLinkModules.15.0
The following response indicates that the AN/ANH driver is configured to
run in Slot 1 (the only AN/ANH slot):
wfLinkModules.wfANLoad.0 = 2147483648
The decimal number 2147483648 represents Slot 1. If the setting is not
2147483648, enter the following command to correct it:
set wfLinkModules.15.0 2147483648;commit
• To display the drivers that are configured to run, enter the following
command:
get wfDrivers.*.0
A combination of the following settings should appear within the list of
drivers, according to your AN or ANH configuration:
wfDrivers.wfQsccSyncLoad.0 = 2147483648
COM ports
wfDrivers.wfQsccEnetLoad.0 = 2147483648
Ethernet ports
(nonrepeating)
wfDrivers.wfRptrLoad.0 = 2147483648
Ethernet repeater
ports (ANH only)
wfDrivers.wfTMS380Load.0 = 2147483648
Token Ring ports
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- About This Guide 15
- Before You Begin 16
- CompuServe 17
- InfoFACTS 18
- World Wide Web 18
- How to Get Help 19
- Conventions 19
- Acronyms 20
- Chapter 1 23
- (continued) 24
- ANH Models 25
- Access Node Software 27
- Router Software 28
- Boot Configuration Options 28
- EZ-Install 29
- The Boot Process 31
- Local Boot 37
- Chapter 2 39
- Booting the Router Routinely 41
- Directed Netboot 42
- Recommendations 43
- Completing a Startup Option 44
- Chapter 3 49
- Setting Up a UNIX Boot Server 49
- Setting Up BOOTP Sockets 50
- Setting Up BOOTPD to Run 51
- Editing the bootptab File 52
- Setting Up a TFTP Server 56
- Editing the inetd.conf File 59
- Verifying the Routes 59
- Rebooting 59
- What to Do Next 60
- Chapter 4 61
- Configuring Network Booting 61
- Creating Configuration Files 62
- Preparing an Image 63
- Configuring Network Booting 67
- 2. Click on Add 68
- 4. Click on OK 69
- 71
- 72
- Enabling Router Interfaces 74
- ??? appears 78
- 1. Click on Client I/F 79
- Chapter 5 83
- Network Boot Client 83
- 84
- 84
- <next 86
- <interface> 86
- Ethernet interface 87
- <interface> 88
- Chapter 6 91
- 93
- About the N11 DCM 97
- The RMON Groups 98
- Ethernet Statistics Group 99
- HostTopN Group 100
- Matrix Group 100
- Filter Group 100
- Packet Capture Group 100
- Enabling the DCM 101
- 103
- 104
- 104
- 105
- 105
- 106
- Disabling DCM 108
- Booting DCM 108
- 2. Click on OK 111
- RMON Implementation Notes 113
- RMON Interoperability Issues 113
- RMON Memory Use 114
- Statistics Group 115
- History Group 115
- Host Group 116
- Filter and Capture Groups 118
- Appendix A 121
- Router Fails to Netboot 123
- <connector> 127
- Displaying Parameter Settings 130
- Debugging the BOOTP Server 131
- Table A-1. BOOTP Messages 132
- <IP_address> 133
- Quick Get Instructions 134
- Upgrading the Software Image 135
- Restoring a Local File System 136
- Appendix B 137
- Global Information Worksheet 139
- Router Protocol Worksheets 141
- OSPF Worksheet 142
- Wide-Area Protocol Worksheets 144
- Frame Relay Worksheet 145
- PPP Standard Worksheet 146
- Appendix C 151
- Implementation Notes 151
- 1: as the volume name 152
- Network Configuration Options 153
- Configuring a Single ANH 154
- Access Node Hub 155
- Configuring Multiple Hubs 156
- Configuring an AUI Port 157
Relacionado con productos y manuales para Software Avaya Connecting BayStack AN and ANH Platforms to a Network
Software Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Manual de usuario
(190 paginas)
(190 paginas)
Software Avaya R4.3 Manual de usuario
(368 paginas)
(368 paginas)
Software Avaya Read Me First: Router Software 11.02 and Site Manager 5.02 Manual de usuario
(10 paginas)
(10 paginas)
Software Avaya Attendant Console Guía de usuario
(96 paginas)
(96 paginas)
Software Avaya B5800 Manual de usuario
(70 paginas)
(70 paginas)
Software Avaya BCM 5.0 - Contact Center - Intelligent Contact Center Manual de usuario
(258 paginas)
(258 paginas)
Software Avaya BCM-IVR 2.1 Guía de usuario
(103 paginas)
(103 paginas)
Software Avaya Bay Command Console Manual de usuario
(130 paginas)
(130 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales