Avaya Connecting BayStack AN and ANH Platforms to a Network Manual de usuario Pagina 153
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Implementation Notes
C-3
• When at the diagnostic prompt, you cannot view the contents of Flash
memory. Be extremely careful to remember the name of the configuration file
when doing a named boot from the Diagnostic Monitor prompt.
Network Configuration Options
This section describes several options for configuring an ANH in a network. It
provides general requirements and recommendations for network configurations
using the ANH, as well as examples of valid configurations.
The basic configuration uses a standalone ANH in a departmental network (see
the section “Configuring a Single ANH”). To accommodate more stations, you
can connect (daisy-chain) multiple ANH systems (see the section “Configuring
Multiple Hubs”).
Ensuring Ethernet Network Compliance
Before configuring any network hardware, use the following rules to assess your
network for compliance with Ethernet operating standards. (Using these rules
allows you to avoid performing the detailed calculations specified in the IEEE
802.3 specifications.)
The network is compliant when it meets all of the following requirements:
• No path through the network contains more than five repeaters.
• No more than 1024 stations are connected (not counting repeaters).
• The entire Ethernet network consists of only IEEE 802.3 components, using
only AUI, 10Base-T, FOIRL, 10Base-F, 10Base-5, or 10Base-2 cables.
• Fiber-optic link attenuation limits are met. (Refer to the attenuation
specifications for the fiber-optic cable, connectors, and transceiver or device
transmitter/receiver ports that you are using.)
• No link is longer than the IEEE 802.3 maximums, given in Table C-
1.
Note: The examples and illustrations in this section show the 8-port ANH, but
they apply to any Bay Networks ANH system.
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- About This Guide 15
- Before You Begin 16
- CompuServe 17
- InfoFACTS 18
- World Wide Web 18
- How to Get Help 19
- Conventions 19
- Acronyms 20
- Chapter 1 23
- (continued) 24
- ANH Models 25
- Access Node Software 27
- Router Software 28
- Boot Configuration Options 28
- EZ-Install 29
- The Boot Process 31
- Local Boot 37
- Chapter 2 39
- Booting the Router Routinely 41
- Directed Netboot 42
- Recommendations 43
- Completing a Startup Option 44
- Chapter 3 49
- Setting Up a UNIX Boot Server 49
- Setting Up BOOTP Sockets 50
- Setting Up BOOTPD to Run 51
- Editing the bootptab File 52
- Setting Up a TFTP Server 56
- Editing the inetd.conf File 59
- Verifying the Routes 59
- Rebooting 59
- What to Do Next 60
- Chapter 4 61
- Configuring Network Booting 61
- Creating Configuration Files 62
- Preparing an Image 63
- Configuring Network Booting 67
- 2. Click on Add 68
- 4. Click on OK 69
- 71
- 72
- Enabling Router Interfaces 74
- ??? appears 78
- 1. Click on Client I/F 79
- Chapter 5 83
- Network Boot Client 83
- 84
- 84
- <next 86
- <interface> 86
- Ethernet interface 87
- <interface> 88
- Chapter 6 91
- 93
- About the N11 DCM 97
- The RMON Groups 98
- Ethernet Statistics Group 99
- HostTopN Group 100
- Matrix Group 100
- Filter Group 100
- Packet Capture Group 100
- Enabling the DCM 101
- 103
- 104
- 104
- 105
- 105
- 106
- Disabling DCM 108
- Booting DCM 108
- 2. Click on OK 111
- RMON Implementation Notes 113
- RMON Interoperability Issues 113
- RMON Memory Use 114
- Statistics Group 115
- History Group 115
- Host Group 116
- Filter and Capture Groups 118
- Appendix A 121
- Router Fails to Netboot 123
- <connector> 127
- Displaying Parameter Settings 130
- Debugging the BOOTP Server 131
- Table A-1. BOOTP Messages 132
- <IP_address> 133
- Quick Get Instructions 134
- Upgrading the Software Image 135
- Restoring a Local File System 136
- Appendix B 137
- Global Information Worksheet 139
- Router Protocol Worksheets 141
- OSPF Worksheet 142
- Wide-Area Protocol Worksheets 144
- Frame Relay Worksheet 145
- PPP Standard Worksheet 146
- Appendix C 151
- Implementation Notes 151
- 1: as the volume name 152
- Network Configuration Options 153
- Configuring a Single ANH 154
- Access Node Hub 155
- Configuring Multiple Hubs 156
- Configuring an AUI Port 157
Relacionado con productos y manuales para Software Avaya Connecting BayStack AN and ANH Platforms to a Network
Software Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Manual de usuario
(190 paginas)
(190 paginas)
Software Avaya R4.3 Manual de usuario
(368 paginas)
(368 paginas)
Software Avaya Read Me First: Router Software 11.02 and Site Manager 5.02 Manual de usuario
(10 paginas)
(10 paginas)
Software Avaya Attendant Console Guía de usuario
(96 paginas)
(96 paginas)
Software Avaya B5800 Manual de usuario
(70 paginas)
(70 paginas)
Software Avaya BCM 5.0 - Contact Center - Intelligent Contact Center Manual de usuario
(258 paginas)
(258 paginas)
Software Avaya BCM-IVR 2.1 Guía de usuario
(103 paginas)
(103 paginas)
Software Avaya Bay Command Console Manual de usuario
(130 paginas)
(130 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales