Avaya Configuring WAN Line Services Manual de usuario Pagina 202
- Pagina / 294
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring WAN Line Services
9-14
117345-B Rev. 00
Before you can group lines, you must create the unused logical lines. To create the
unused logical lines:
Site Manager Procedure
You do this System responds
1. Start at the MCE1 or MCT1 Logical Lines
window. (See Chapter 7
for details.)
2. Click on an unconfigured MCE1 or MCT1
connector in the Configuration Manager
window.
The Port Application window opens.
3. Set the Port Application Mode parameter
to
NONPRI
,
then click on
OK
.
The Edit Clock Parameters window
opens.
4. Select a primary and secondary clock
source option, then click on
OK
.
The MCE1 or MCT1 Port Parameters
window opens
.
5. Set the port parameters, then click on
OK
. The MCE1 or MCT1 Logical Lines
window opens.
6. After customizing the port parameters,
click on
Add
.
The Add Circuit window opens.
Do not click on
OK
in the Add Circuit
window. Selecting OK adds a single-line
circuit for this logical line. You cannot
create a multiline circuit from a single-line
circuit.
7. Click on
Cancel
to create an unused
logical line.
The MCE1 or MCT1 Logical Lines
window reopens.
8. Repeat steps 7 and 8 for each unused
logical line you want to create.
The MCE1 or MCT1 Logical Lines
window now lists the unused logical lines.
Figure 9-7
shows four unused logical
lines.
- Configuring 1
- WAN Line Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117345-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 24
- Chapter 1 27
- Getting Started 27
- To edit a circuit: 33
- Figure 1-4. Edit Lines Window 34
- Chapter 2 35
- Setting the BofL Timeout 41
- Setting the MTU 41
- Configuring Clocking Signals 43
- Setting the Signal Mode 45
- Setting Minimum Frame Spacing 49
- Setting the CRC Size 52
- Setting the Signaling Method 54
- Setting the Line Coding 55
- Configuring KG84A Security 55
- Setting the Retry Count 59
- Setting the Link Idle Timer 60
- Setting the Cable Type 61
- Setting the Retry Timer 61
- Setting a Priority 62
- Setting the Hold Down Time 63
- Setting the IFTF Pattern 65
- Chapter 3 77
- Asynchronous Services 77
- for information 78
- Setting the Remote IP Address 79
- Specifying the Remote Port 80
- Specifying the Local Port 80
- Setting the Idle Timer 81
- Chapter 4 83
- Setting the Option Mode 85
- Loopback Test Modes 89
- AN/ANH/ARN 90
- Chapter 5 93
- Enabling or Disabling BofL 96
- Using the BCC 100
- Using Site Manager 100
- Configuring HSSI Services 101
- Chapter 6 103
- Editing T1 Services 104
- Setting the T1 Frame Type 105
- Configuring WAN Line Services 106
- Figure 6-2. Bipolar Format 106
- Specifying Line Buildout 107
- Assigning Channel Functions 108
- Editing E1 Services 109
- Enabling or Disabling CRC 111
- Setting the Clock Source 111
- Chapter 7 113
- Setting the Clock Parameters 116
- Configuring a DS0A Connection 129
- Setting Parameters 131
- Table 7-2 132
- Defining Logical Lines 133
- (MCT1 Example) 134
- Circuit Name: MCE1_31_1 135
- Circuit name: MCE1_231_1 135
- (MCE1 Example) 136
- See the following sections: 137
- Caution: 139
- Assigning Timeslots 144
- About the Tests 149
- Setting Port Test Parameters 150
- Running Port Tests 153
- Running Logical Line Tests 158
- Send Command Function 159
- Chapter 8 161
- Configuring FT1 Services 161
- Configuring an FT1 Port 162
- Defining Logical Line 172
- Circuit name: 174
- Chapter 9 189
- Types of Multiline Circuits 190
- Multiline Example 191
- Software Considerations 192
- Logical Lines (MCE1 Example) 205
- Appendix A 209
- Asynchronous Line Parameters 210
- DSU/CSU Parameters 216
- E1 Line Parameters 218
- HSSI Line Parameters 221
- LAPB Parameters 226
- MCE1 Port Parameters 233
- MCT1 Port Parameters 237
- FT1 Port Parameters 252
- FT1 Logical Line Parameters 258
- Synchronous Line Parameters 263
- T1 Line Parameters 282
- Glossary 287
Relacionado con productos y manuales para Redes Avaya Configuring WAN Line Services
Redes Avaya X.25 Manual de usuario
(148 paginas)
(148 paginas)
Redes Avaya BayRS Version 13.10 Manual de usuario
(104 paginas)
(104 paginas)
Redes Avaya Configuring BFE Services Manual de usuario
(180 paginas)
(180 paginas)
Redes Avaya Configuring IP Services Manual de usuario
(585 paginas)
(585 paginas)
Redes Avaya BCM1000 Manual de instalación
(90 paginas)
(90 paginas)
Redes Avaya BCM 4.0 Networking Guía de configuración
(758 paginas)
(758 paginas)
Redes Avaya Configuring IP Services Manual de usuario
(610 paginas)
(610 paginas)
Redes Avaya BCM3.x Manual de usuario
(28 paginas)
(28 paginas)
Redes Avaya Configuring IPX Services Manual de usuario
(250 paginas)
(250 paginas)
Redes Avaya V.34 Manual de usuario
(34 paginas)
(34 paginas)
Redes Avaya 1D5 aviso
(40 paginas)
(40 paginas)
Redes Avaya Configuring DLSw Services Manual de usuario
(272 paginas)
(272 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales