Avaya Configuring Frame Relay Services Manual de usuario Pagina 152
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring Frame Relay Services
5-42
308624-14.10 Rev 01
To set X.213 priority values, navigate to the prompt for the SVC you want to
modify (for example,
box; serial/3/2; frame-relay/3/2; service/8.0.32;
svc-options/toronto
) and enter any of the following parameters:
data-priority
<integer>
data-priority-minimum
<integer>
gain-priority
<integer>
gain-priority-minimum
<integer>
keep-priority
<integer>
keep-priority-minimum
<integer>
integer
can be a value from 0 to 15, with 0 as the lowest priority and 14 as the
highest. A value of 15 means unspecified.
For example, the following command line sets a data priority of 9
for SVC options:
svc-options/toronto# data-priority 9
svc-options/toronto#
Using Site Manager
To set X.213 priority value
s,
complete the following tasks
:
Site Manager Procedure
You do this System responds
1. In the Configuration Manager window,
choose
Protocols
.
The Protocols menu opens.
2. Choose
Frame Relay
. The Frame Relay menu opens.
3. Choose
Services
. The Frame Relay Service List window
opens.
4. Choose the service record that includes
the SVC that you want to configure for
traffic shaping.
5. Click on
SVCs
. The Frame Relay SVC Options List for
Service window opens.
(continued)
- Configuring Frame Relay 1
- Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308624-14.10 Rev 01 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Hard-Copy Technical Manuals 21
- How to Get Help 22
- Chapter 1 23
- Frame Relay Overview 23
- Introduction to Frame Relay 24
- Permanent Virtual Circuits 25
- Switched Virtual Circuits 25
- PVC and SVC Comparison 26
- Frame Relay Packets 27
- . Note, however 28
- Management Protocols 29
- LAPF Operational States 31
- SVC Signaling 33
- Table 1-3. Network Timers 34
- Message Processing 35
- Frame Relay Service Records 36
- Frame Relay Access Modes 37
- Direct Access Mode 38
- Hybrid Access Mode 38
- Source Routing 40
- RFC 1490 40
- Address Resolution for PVCs 40
- Address Resolution for SVCs 41
- Traffic Control 41
- Data Compression 42
- Data Encryption 43
- Protocol Prioritization 43
- Congestion Control 44
- Traffic Shaping 45
- Quality of Service 47
- Traffic Shaping for SVCs 49
- Inactivity Timing for SVCs 55
- X.213 Priority for SVCs 55
- Multiline for PVCs 57
- PVC Pass-Through 59
- Frame Relay Dial Services 60
- Chapter 2 63
- Starting Frame Relay 63
- Configuring PVCs and SVCs 66
- To configure a PVC: 67
- Configuring an SVC 68
- Chapter 3 71
- Selecting a Management Type 72
- Setting XOFF Control 74
- Selecting a DLCI Address Type 75
- Monitoring the Connection 77
- Full Enquiry Interval 78
- Deleting Frame Relay 82
- Chapter 4 83
- Adding Service Records 85
- Deleting Service Records 86
- Enabling Multicast 92
- Configuring PVC Pass-Through 95
- Mapping Pass-Through PVCs 96
- Using Site Manager 100
- Using the BCC 100
- <integer> 101
- <value> 102
- Using Traffic Shaping 103
- Excess Burst 105
- Committed Burst 105
- CIR (Throughput) 106
- Customizing PVCs 109
- Removing Multiline Services 110
- Chapter 5 111
- Customizing SVCs 111
- Call Screening and Blocking 115
- SVC Screening 116
- SVC Screen Usage 116
- Disabling SVCs 119
- Disconnecting Active SVCs 120
- Station Type 122
- Initiation Mode 123
- Retransmission Timer 123
- Idle Timer 124
- Retransmission Limit 124
- Information Limit 124
- Window Size 125
- (continued) 126
- Maximum SVCs 128
- Setup Timer 128
- Disconnect Timer 129
- Release Timer 129
- Call Proceeding Timer 130
- Status Enquiry Timer 130
- Status Enquiry Retry 131
- <direction> 133
- Enabling Traffic Shaping 143
- Appendix A 155
- Site Manager Parameters 155
- Interface Parameters 156
- Figure A-2 157
- SVC LAPF Parameters 166
- SVC Signaling Parameters 171
- Service Name Parameter 176
- <line_number> 177
- <circuit_number> 177
- PVC Parameters 178
- PVC Service Record Parameters 180
- Multiline Algorithm Parameter 186
- C Service Record Parameters 189
- SVC Options Parameters 195
- Appendix B 211
- Table B-1. RIP Parameters 212
- Appendix C 219
- Monitoring Frame Relay Using 219
- Online Help for show Commands 220
- <dlci> 222
- <multiline_name> 222
- <name> 223
- (continued) 229
Relacionado con productos y manuales para Redes Avaya Configuring Frame Relay Services
Redes Avaya BCM50 Manual de usuario
(52 paginas)
(52 paginas)
Redes Avaya IPv6 Manual de usuario
(157 paginas)
(157 paginas)
Redes Avaya V.34 Manual de usuario
(32 paginas)
(32 paginas)
Redes Avaya Configuring APPN Services Manual de usuario
(146 paginas)
(146 paginas)
Redes Avaya BCM450 Guía de configuración
(14 paginas)
(14 paginas)
Redes Avaya X.25 Manual de usuario
(104 paginas)
(104 paginas)
Redes Avaya B179 Nota de aplicación
(37 paginas)
(37 paginas)
Redes Avaya BayRS Version 15.3.0.0 aviso
(74 paginas)
(74 paginas)
Redes Avaya Configuring PPP Services Manual de usuario
(118 paginas)
(118 paginas)
Redes Avaya BCM50/450 Guía de configuración
(38 paginas)
(38 paginas)
Redes Avaya Configuring RADIUS Manual de usuario
(116 paginas)
(116 paginas)
Redes Avaya Configuring MPOA Services Manual de usuario
(148 paginas)
(148 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales