Avaya Configuring Frame Relay Services Manual de usuario Pagina 102
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring Frame Relay Services
4-20
308624-14.10 Rev 01
Congestion Counter
To change the value for the congestion counter, navigate to the prompt for the
PVC you want to modify (for example,
box; serial/1/2; frame-relay/1/2;
orlando; pvc/1/2/51
) and enter:
congestion-counter
<integer>
integer
is the maximum number of congestion notifications the router can receive
during the congestion timer period before it stops transmitting data.
The counter value can be from 1 to 500 notifications. The default is 20.
For example, the following command line sets a congestion counter of 30
notifications:
pvc/1/2/51##
congestion-counter 30
pvc/1/2/51##
Congestion Method
To change the value for the congestion method, navigate to the prompt for the
PVC you want to modify (for example,
box; serial/1/2; frame-relay/1/2;
newyork; pvc/1/2/51
) and enter:
congestion-method
<value>
value
can be:
throttle-then-shutdown
-- first queues traffic when congestion occurs, and then
terminates the VC if throttling does not alleviate congestion. This option is valid
only when traffic shaping is enabled.
shutdown
--
the default, terminates the VC when congestion occurs.
throttle
-- queues traffic when congestion occurs; traffic resumes when congestion
clears. This option is valid only when traffic shaping is enabled.
inherit
-- specifies that this VC will use the value of the interface’s congestion
method setting.
For example, the following command line sets a congestion method of throttle:
pvc/1/2/51#
congestion-method throttle
pvc/1/2/51#
- Configuring Frame Relay 1
- Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308624-14.10 Rev 01 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Hard-Copy Technical Manuals 21
- How to Get Help 22
- Chapter 1 23
- Frame Relay Overview 23
- Introduction to Frame Relay 24
- Permanent Virtual Circuits 25
- Switched Virtual Circuits 25
- PVC and SVC Comparison 26
- Frame Relay Packets 27
- . Note, however 28
- Management Protocols 29
- LAPF Operational States 31
- SVC Signaling 33
- Table 1-3. Network Timers 34
- Message Processing 35
- Frame Relay Service Records 36
- Frame Relay Access Modes 37
- Direct Access Mode 38
- Hybrid Access Mode 38
- Source Routing 40
- RFC 1490 40
- Address Resolution for PVCs 40
- Address Resolution for SVCs 41
- Traffic Control 41
- Data Compression 42
- Data Encryption 43
- Protocol Prioritization 43
- Congestion Control 44
- Traffic Shaping 45
- Quality of Service 47
- Traffic Shaping for SVCs 49
- Inactivity Timing for SVCs 55
- X.213 Priority for SVCs 55
- Multiline for PVCs 57
- PVC Pass-Through 59
- Frame Relay Dial Services 60
- Chapter 2 63
- Starting Frame Relay 63
- Configuring PVCs and SVCs 66
- To configure a PVC: 67
- Configuring an SVC 68
- Chapter 3 71
- Selecting a Management Type 72
- Setting XOFF Control 74
- Selecting a DLCI Address Type 75
- Monitoring the Connection 77
- Full Enquiry Interval 78
- Deleting Frame Relay 82
- Chapter 4 83
- Adding Service Records 85
- Deleting Service Records 86
- Enabling Multicast 92
- Configuring PVC Pass-Through 95
- Mapping Pass-Through PVCs 96
- Using Site Manager 100
- Using the BCC 100
- <integer> 101
- <value> 102
- Using Traffic Shaping 103
- Excess Burst 105
- Committed Burst 105
- CIR (Throughput) 106
- Customizing PVCs 109
- Removing Multiline Services 110
- Chapter 5 111
- Customizing SVCs 111
- Call Screening and Blocking 115
- SVC Screening 116
- SVC Screen Usage 116
- Disabling SVCs 119
- Disconnecting Active SVCs 120
- Station Type 122
- Initiation Mode 123
- Retransmission Timer 123
- Idle Timer 124
- Retransmission Limit 124
- Information Limit 124
- Window Size 125
- (continued) 126
- Maximum SVCs 128
- Setup Timer 128
- Disconnect Timer 129
- Release Timer 129
- Call Proceeding Timer 130
- Status Enquiry Timer 130
- Status Enquiry Retry 131
- <direction> 133
- Enabling Traffic Shaping 143
- Appendix A 155
- Site Manager Parameters 155
- Interface Parameters 156
- Figure A-2 157
- SVC LAPF Parameters 166
- SVC Signaling Parameters 171
- Service Name Parameter 176
- <line_number> 177
- <circuit_number> 177
- PVC Parameters 178
- PVC Service Record Parameters 180
- Multiline Algorithm Parameter 186
- C Service Record Parameters 189
- SVC Options Parameters 195
- Appendix B 211
- Table B-1. RIP Parameters 212
- Appendix C 219
- Monitoring Frame Relay Using 219
- Online Help for show Commands 220
- <dlci> 222
- <multiline_name> 222
- <name> 223
- (continued) 229
Relacionado con productos y manuales para Redes Avaya Configuring Frame Relay Services
Redes Avaya BCM50 Manual de usuario
(52 paginas)
(52 paginas)
Redes Avaya IPv6 Manual de usuario
(157 paginas)
(157 paginas)
Redes Avaya V.34 Manual de usuario
(32 paginas)
(32 paginas)
Redes Avaya Configuring APPN Services Manual de usuario
(146 paginas)
(146 paginas)
Redes Avaya BCM450 Guía de configuración
(14 paginas)
(14 paginas)
Redes Avaya X.25 Manual de usuario
(104 paginas)
(104 paginas)
Redes Avaya B179 Nota de aplicación
(37 paginas)
(37 paginas)
Redes Avaya BayRS Version 15.3.0.0 aviso
(74 paginas)
(74 paginas)
Redes Avaya Configuring PPP Services Manual de usuario
(118 paginas)
(118 paginas)
Redes Avaya BCM50/450 Guía de configuración
(38 paginas)
(38 paginas)
Redes Avaya Configuring RADIUS Manual de usuario
(116 paginas)
(116 paginas)
Redes Avaya Configuring MPOA Services Manual de usuario
(148 paginas)
(148 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales