Avaya Reference for the Business Policy Switch 2000 Command Line Interface Release 1.2 Manual de usuario Pagina 185
- Pagina / 200
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 6 Policy-enabled networks and QoS 185
Reference for the Business Policy Switch 2000 Command Line Interface
Table 108 qos policy command parameters and variables
Parameters
and variables
Description
<polid> Enter an integer to specify the QoS policy; range is 1 to 65535.
create Creates the QoS policy.
name
<polname>
Assigns a name to the QoS policy with the designated policy ID. Enter
the name for the policy; maximum is 16 alphanumeric characters.
if-group
<ifgroup>
Enter the interface group name to which this policy applies.
filter-set-type
{ip|l2}
Enter the type of filter set associated with this policy:
• ip—specifies IP filter set
• l2—specifies Layer 2 filter set
filter-set <setid> Enter the filter set ID associated with this policy; range is 1 to 65535.
filter-set-name
<setname>
Enter the name of the filter set associated with this policy.
meter <metid> Enter meter ID associated with this policy range is 1 to 65535.
Indirectly specifies, through the meter, the action or actions associated
with this policy.
meter-name
<metname>
Enter the meter name associated with this policy; maximum of 16
alphanumeric characters. Indirectly specifies, through the meter, the
action or actions associated with this policy.
track-statistics
{enable|disable}
Enables maintaining policing statistics on the specified flow. Default is
based on value of setting of
qosagent police-statistics
command.
order <order> Specifies the evaluation order of this policy in relation to other policies
associated with the same interface group. Enter order number; range
is 1 to 65535.
Note: Policies with a lower order value are evaluated before policies
with a higher order number. Evaluation goes from lowest value to
highest.
delete Deletes the specified QoS policy.
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 1.2 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- Contents 5
- Chapter 5 10
- Chapter 6 10
- Appendix A 11
- 12 Contents 12
- About this guide 19
- Before you begin 19
- Text conventions 20
- Related publications 21
- How to get help 22
- Preface 23 23
- 24 Preface 24
- Chapter 1 25
- CLI Basics 25
- Stacking compatibility 26
- Chapter 1 CLI Basics 27 27
- CLI command modes 28
- Chapter 1 CLI Basics 29 29
- 30 Chapter 1 CLI Basics 30
- Port numbering 32
- IP notation 33
- Accessing the CLI 33
- 34 Chapter 1 CLI Basics 34
- Figure 2 BPS 2000 banner 34
- Setting the CLI password 36
- Getting help 37
- Basic navigation 37
- General navigation commands 38
- Keystroke navigation 39
- BPS2000#show stack-info 46
- BPS2000#show stack-oper-mode 50
- Chapter 1 CLI Basics 51 51
- 52 Chapter 1 CLI Basics 52
- Chapter 2 53
- General CLI commands 53
- Setting the terminal 54
- Configuration Filename: 59
- Setting Telnet access 64
- Setting boot parameters 69
- Setting TFTP parameters 72
- Upgrading images 75
- Displaying interfaces 76
- Setting SNMP parameters 77
- Setting the system event log 82
- Displaying port statistics 85
- Enabling or disabling a port 87
- Setting port speed 89
- Enabling Autopology 92
- Enabling flow control 93
- Enabling rate-limiting 96
- 212160-A 100
- Chapter 3 101
- Security 101
- Using MAC address security 106
- command is: 107
- Parameters 111
- Description 111
- Using EAPOL-based security 112
- Using RADIUS authentication 115
- 118 Chapter 3 Security 118
- Chapter 4 119
- Using MLT 132
- Using port-mirroring 135
- VLANs and IGMP 139
- 140 Chapter 5 VLANs and IGMP 140
- Parameters and 141
- Chapter 5 VLANs and IGMP 145 145
- Using IGMP snooping 153
- 156 Chapter 5 VLANs and IGMP 156
- Displaying QoS parameters 158
- IP Filter Sets 163
- Resetting 168
- Configuring COPS 168
- Configuring QoS actions 180
- Configuring QoS meters 181
- Gathering QoS statistics 183
- Configuring QoS policies 184
- Reordering packets 186
- Command List 187
- 188 Appendix A Command List 188
- Appendix A Command List 189 189
- 190 Appendix A Command List 190
- Appendix A Command List 191 191
- 192 Appendix A Command List 192
- Appendix A Command List 193 193
- 194 Appendix A Command List 194
Relacionado con productos y manuales para Los conmutadores de red Avaya Reference for the Business Policy Switch 2000 Command Line Interface Release 1.2
(96 paginas)
(16 paginas)Related products and manuals for Power supply units Clear-Com PS-10K
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales