Avaya Configuring ATM Services Manual de usuario Pagina 274
- Pagina / 411
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring ATM Services
8-4
117374-B Rev. 00
Specifying the MPS Control ATM Address
To exist within the ATM environment, the MPS must be part of a sevice record. In
automatic mode, the MPS uses the information from the service record to obtain
address information from the ILMI address registration. In manual mode,
however, you must assign the ATM address that the MPS uses.
To fully specify the MPOA service record address you must set the following
address parameters:
• Control ATM address network prefix
• Control ATM address user part
Setting the Control ATM Address Network Prefix
The control ATM address network prefix specifies the ATM domain of which the
MPS is a part. This 13-byte portion of the ATM address can range from
XX000000000000000000000000 to XXFFFFFFFFFFFFFFFFFFFFFFFF.
The XX byte must contain 39, 45, or 47. These values define the authority and
format identifier (AFI). The AFI byte identifies the group responsible for
allocating the prefix and the format the prefix uses. For more information about
the AFI byte, refer to the ATM Forum UNI specification.
Entering an ATM address network prefix is optional. If you do not enter a network
prefix in the specified range, the MPS accepts the first prefix value that it receives
from the switch.
Note:
These parameters also appears in the MPS List window for display
purposes only. You must configure the control ATM address at the service
record level.
- Configuring ATM 1
- Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117374-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 25
- Chapter 1 27
- Understanding ATM, MPOA, and 27
- ATM General Information 28
- Figure 1-2. ATM Cell Header 29
- Data Transmission 30
- VP = Virtual path 31
- VC = Virtual channel 31
- ATM Layers 32
- Table 1-1. Maximum Bandwidth 34
- ATM0005A 35
- Caution: 37
- Data Encapsulation Methods 38
- Encapsulation Rules for PVCs 42
- PVC Access Methods 43
- SVC Access Methods 48
- Assigning ATM Addresses 48
- ATM Traffic Parameters 49
- ARP and Inverse ARP Support 53
- ATM Error Checking 53
- Converting Mb/s to Cells/s 53
- ATM Address Resolution 57
- ATM LAN Emulation Concepts 59
- LAN Emulation Connectivity 60
- LAN Emulation Components 60
- Redundant LES/BUS 61
- LAN Emulation States 62
- MPOA Logical Components 65
- MPOA Basic Elements 66
- ATM00002 68
- Figure 1-15 69
- For More Information 71
- Chapter 2 73
- ATM Router Redundancy 73
- Starting Configuration Tools 74
- Starting ATM Services 74
- Defining PVC Service 76
- Defining Classical IP Service 76
- Defining LEC Service 77
- Adding IP 79
- Adding IPX 79
- Adding PVCs 85
- Starting the MPOA Server 86
- Configuring the MPS 89
- Redundency 91
- Deleting ATM from the Router 95
- Chapter 3 99
- Using the BCC 100
- Defining the Interface MTU 101
- Using Site Manager 102
- Assigning the Framing Mode 107
- Specifying DS-3 Line Buildout 109
- Customizing an ATM Interface 115
- Autogenerating ATM Addresses 116
- Where to Go Next 120
- Chapter 4 121
- Customizing Signaling 121
- Defining Signaling 122
- Setting Connection Thresholds 129
- Defining Signaling Timers 135
- Configuring ATM Services 136
- Defining Retransmissions 142
- Pacing Calls 145
- Defining ILMI 146
- Defining Control VCs 154
- Changing VPI Numbers 155
- Changing VCI Numbers 157
- ) and enter: 158
- Table 4-2. Valid PCR Ranges 160
- Defining SSCOP/Signaling AAL 176
- Modifying SAAL Timers 180
- Defining PDU Values 182
- Chapter 5 189
- Customizing PVC Service 189
- Records and PVCs 189
- Deleting a Service Record 193
- Setting the PCR 197
- Setting the SCR 199
- Setting the MBS 201
- Setting the Transmit SDU Size 202
- Setting the Receive SDU Size 204
- PVC to NLPID encapsulation: 206
- Copying a PVC 207
- Deleting a PVC 208
- Chapter 6 211
- Chapter 7 223
- Customizing LAN Emulation 223
- Service Records and Clients 223
- Specifying an Owner 237
- Assigning ATM LES Addresses 238
- Modifying a LES/BUS Entry 243
- Deleting a LES Entry 244
- Setting the Control Timeout 251
- Setting the Aging Time 255
- (continued) 261
- Setting the Flush Timeout 263
- Specifying a LECS ATM Address 265
- Chapter 8 271
- (continued) 275
- Defining MPS Timers 280
- Setting the Give Up Time 284
- Defining MPS Cache Values 286
- Maximum Cache Size 287
- Deleting an Individual MPS 288
- Chapter 9 291
- Appendix A 295
- Site Manager Parameters 295
- Accessing ATM Parameters 296
- Using the Menu Path 297
- ATM Line Parameters 298
- ATM Interface Parameters 304
- ATM Service Record Parameters 307
- LAN Emulation Parameters 318
- LES Parameter Descriptions 327
- ATM Signaling Parameters 329
- ATM ILMI Signaling Parameters 340
- ATM Signaling AAL Parameters 347
- MPOA Parameters 351
- NHRP Parameters 359
- Adjacent Host Parameters 370
- Appendix B 373
- <slot> 374
- <connector> 374
- <servicename> 378
- <ip address> 381
- (flag) and filter argument: 386
- Appendix C 391
- NHRP Overview 392
- Configuring NHRP 393
- Editing an NHRP Record 399
- Disabling an NHRP Record 400
- Deleting NHRP 400
- Index-10 410
- Index-11 411
Relacionado con productos y manuales para Manuales de software Avaya Configuring ATM Services
Manuales de software Avaya Router Guía de inicio rápido
(132 paginas)
(132 paginas)
Manuales de software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manual de usuario
(130 paginas)
(130 paginas)
Manuales de software Avaya LT2P Manual de usuario
(76 paginas)
(76 paginas)
Manuales de software Avaya BCM 4.0 Guía de usuario
(42 paginas)
(42 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.258 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales