Avaya R2MFC Guía de configuración Pagina 48
- Pagina / 106
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
48 Chapter 4 Configuring the R2MFC MBM
N0027684 01
Signaling
The list of layer 2 signaling parameters are listed in Table 4.
Layer 3 signaling parameters are listed in Table 5.
Configuring the PRI (internal) link
The BCM installs default settings for MBMs, which vary depending on the region chosen during
start up. These settings for the R2MFC MBM can be verified and customized through the Unified
Manager. Perform the following steps to verify and custome the PRI (internal) link:
1 Open the Unified Manager. See the Programming guide for the host system for an explanation
of how to use Unified Manager.
2 Click the Configuration button on the Unified Manager main page.
The Unified Manager main display opens.
3 Enter your Unified Manager login credentials.
4 Select the appropriate Bus # under the Resources > Media Bay Modules headings in the
navigation tree.
The Bus # information frame displays. See Figure 17 on page 49 for an example of the screen
layout for an R2MFC MBM configured on Bus 06.
Table 4 Layer 2 signaling parameters
Parameter Operational Value
D-channel LAP D
Window size 7
Modulo 128
Table 5 Layer 3 signaling parameters
Parameter Operational Value
Protocol ETSI Euro-ISDN (ETS 300 102). The R2MFC
MBM upper board is the NETWORK side, so the
BCM must be configured as USER side.
Incoming calls from CO to BCM - Digit dialing
mode
Overlap. Every digit is passed to the BCM; the
BCM determines when the number is complete.
The call can be set up immediately after the last
digit is dialed.
Outgoing calls from BCM to CO - Digit dialing
mode
Overlap - for systems requiring second dial tone
from the R2MFC MBM.
Bearer capability for calls initiated by BCM R2MFC accepts bearer capability requests of
services: voice, audio, fax, modem.
Bearer capability for calls initiated from the
R2MFC MBM to the BCM
Bearer capability indicates a normal voice
service.
- R2MFC Media Bay Module 1
- Trademarks 2
- Enhanced 911 Configuration 3
- Radio-frequency Interference 3
- Hearing Aid Compatibility 4
- Important Safety Instructions 4
- Limited Warranty 7
- Warranty Repair Services 8
- After Warranty Service 8
- Contents 9
- 14 Figures 14
- Tables 16
- Before you begin 17
- How to get help 18
- Preface 19 19
- Acronyms 20
- Chapter 1 21
- Overview 21
- R2MFC MBM faceplate elements 22
- System Status LEDs 23
- Config DIP switches 23
- RS232 port 24
- E1 Status LEDs 24
- Bantam jacks 24
- BNC and RJ-48 connectors 24
- Power connectors 24
- MBM DIP switches 25
- 26 Chapter 1 Overview 26
- Chapter 2 27
- Installation process map 28
- R2MFC MBM setup requirements 29
- Environment checklist 30
- Electrical requirements 30
- Software requirements 30
- Chapter 3 31
- Installing the R2MFC MBM 31
- Installing an R2MFC MBM 32
- Reconnecting the equipment 33
- Removing an R2MFC MBM 35
- Wiring an R2MFC MBM 37
- Chapter 4 41
- Configuring the R2MFC MBM 41
- Physical line characteristics 42
- E1 framing 42
- Line signaling 42
- Register signaling 43
- End of dialing (outgoing) 44
- Disable ANI 44
- Default category 44
- Default subscriber status 44
- Setting Config DIP switches 45
- E1 Framing 47
- Signaling 48
- Turning on second dial tone 52
- Chapter 5 55
- R2MFC MBM maintenance 55
- Clock synchronization 56
- Diagnostic tools 57
- Alarms Measurements 58
- Alarms propagation 59
- Faceplate LEDs 60
- Logs and traces 61
- Error messages 61
- Replacing an R2MFC MBM 62
- Upgrading firmware 63
- Chapter 6 67
- Command Line Interface (CLI) 67
- Accessing the CLI 68
- Commands 69
- LOad directory 69
- INfo directory 69
- VIew directory 70
- CNtrl directory 71
- COnfig directory 73
- ALarm directory 75
- SWerr directory 77
- MFC directory 78
- R2 directory 81
- PRI directory 83
- Appendix A 85
- Country code defaults 87
- MFC register signaling 88
- Mexico Config 2 89
- Brazil Config 1 92
- Brazil Config 2 94
- Argentina Config 1 96
- N0027684 01 100
- Appendix B 101
- Appendix C 103
- MFC Signal Definitions 103
- 104 MFC Signal Definitions 104
- Appendix D 105
- CLI Cable Pinout 105
- 106 CLI Cable Pinout 106
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales