Avaya R2MFC Guía de configuración Pagina 44
- Pagina / 106
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
44 Chapter 4 Configuring the R2MFC MBM
N0027684 01
End of dialing (outgoing)
End of dialing in outgoing calls is indicated by MFC signal “I15” (or equivalent country-specific
signal). This signal is sent if the far-end requests next digit beyond the last digit of the dialed
number.
When R2MFC MBM originates a call to the CO, the R2MFC MBM has already received the
whole dialed number from the BCM. This is because the digits are passed from BCM to the MBM
by PRI “en-bloc.” This operation mode means that BCM determines user end-of-dialing either by
number of digits, explicit input from user (for example, the “#” digit), or timeout.
Disable ANI
The ANI request option can be disabled. When disabled:
• Incoming call — R2MFC MBM does not request ANI.
• Outgoing call — When far end requests ANI, R2MFC MBM answers “ANI not available.”
Default category
The MFC subscriber category, sent by R2MFC MBM in outgoing calls, is fixed. The default
category for all countries is II1 (subscriber without priority). If needed, the default can be changed
by CLI.
Default subscriber status
The user can set default subscriber status (for example, free, busy, and vacant number) for
incoming calls. When this feature is enabled, the R2MFC MBM in an incoming call sends the
preset default subscriber status, instead of the status received from the PRI status.
The subscriber status option is not enabled in R2MFC MBM; therefore, the subscriber status is
translated from ISDN message to MFC, and vice versa.
Minimum (or fixed) number
length and timer
Minimal number of digits Receiving minimum number of
digits + optional number of
digits means end of dial
(maximum length reached)
When a fixed length number is
always expected, set the
optional number of digits to 0.
No
Minimum (or fixed) number
length and timer
Optional number of additional
digits
No
Minimum (or fixed) number
length and timer
Interdigit timer in the minimal
interval (long timer)
Expiry of the long timer means
MFC error - number
incomplete.
No
Minimum (or fixed) number
length and timer
Interdigit timer in the optional
interval (short timer)
Expiry of the short timer
means end of dial.
No
Table 2 Minimum (or fixed) number length + timer parameters (Sheet 2 of 2)
Option Parameters Meaning Default
- R2MFC Media Bay Module 1
- Trademarks 2
- Enhanced 911 Configuration 3
- Radio-frequency Interference 3
- Hearing Aid Compatibility 4
- Important Safety Instructions 4
- Limited Warranty 7
- Warranty Repair Services 8
- After Warranty Service 8
- Contents 9
- 14 Figures 14
- Tables 16
- Before you begin 17
- How to get help 18
- Preface 19 19
- Acronyms 20
- Chapter 1 21
- Overview 21
- R2MFC MBM faceplate elements 22
- System Status LEDs 23
- Config DIP switches 23
- RS232 port 24
- E1 Status LEDs 24
- Bantam jacks 24
- BNC and RJ-48 connectors 24
- Power connectors 24
- MBM DIP switches 25
- 26 Chapter 1 Overview 26
- Chapter 2 27
- Installation process map 28
- R2MFC MBM setup requirements 29
- Environment checklist 30
- Electrical requirements 30
- Software requirements 30
- Chapter 3 31
- Installing the R2MFC MBM 31
- Installing an R2MFC MBM 32
- Reconnecting the equipment 33
- Removing an R2MFC MBM 35
- Wiring an R2MFC MBM 37
- Chapter 4 41
- Configuring the R2MFC MBM 41
- Physical line characteristics 42
- E1 framing 42
- Line signaling 42
- Register signaling 43
- End of dialing (outgoing) 44
- Disable ANI 44
- Default category 44
- Default subscriber status 44
- Setting Config DIP switches 45
- E1 Framing 47
- Signaling 48
- Turning on second dial tone 52
- Chapter 5 55
- R2MFC MBM maintenance 55
- Clock synchronization 56
- Diagnostic tools 57
- Alarms Measurements 58
- Alarms propagation 59
- Faceplate LEDs 60
- Logs and traces 61
- Error messages 61
- Replacing an R2MFC MBM 62
- Upgrading firmware 63
- Chapter 6 67
- Command Line Interface (CLI) 67
- Accessing the CLI 68
- Commands 69
- LOad directory 69
- INfo directory 69
- VIew directory 70
- CNtrl directory 71
- COnfig directory 73
- ALarm directory 75
- SWerr directory 77
- MFC directory 78
- R2 directory 81
- PRI directory 83
- Appendix A 85
- Country code defaults 87
- MFC register signaling 88
- Mexico Config 2 89
- Brazil Config 1 92
- Brazil Config 2 94
- Argentina Config 1 96
- N0027684 01 100
- Appendix B 101
- Appendix C 103
- MFC Signal Definitions 103
- 104 MFC Signal Definitions 104
- Appendix D 105
- CLI Cable Pinout 105
- 106 CLI Cable Pinout 106
© 2020, manymanuals.es. Todos los derechos reservados | 0.245 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales