Avaya R2MFC Guía de configuración Pagina 45
- Pagina / 106
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 4 Configuring the R2MFC MBM 45
R2MFC Media Bay Module Installation and Configuration Guide
Configuring the MFCR2 (external) link
The MFCR2 (external) link is configured directly on the R2MFC MBM by setting DIP switches,
and using a CLI on the R2MFC MBM. Standard predefined configurations already exist, and must
be used, whenever possible. Country code configurations set, by DIP switches, are hard-coded,
and can be changed only by using the CLI. See “Setting Config DIP switches” for a description of
how to set the predefined country code and second dial tone settings. The CLI can be used to
create a customized country codes. See “Creating a customized country code” on page 46 for a
procedure on how to create the customized country code.
Setting Config DIP switches
The Config DIP switch settings include diagnostic mode, country codes, and second dial tone.
Country codes include the default settings for the connection (link) for the country selected. See
Appendix A, “Config DIP switch settings and definitions,” on page 85 for the country code DIP
switch settings and their specifications.
Perform the following steps to set the Config DIP switches:
1 Power down the BCM.
2 Set the Config DIP switches to the appropriate country code and second dial tone setting that
coincides with your location.
See Appendix A, “Config DIP switch settings and definitions,” on page 85 for predefined
country code DIP switch settings and their specifications.
See “Turning on second dial tone” on page 52 for the procedure to turn on second dial tone.
The Config DIP switch settings are divided into the following parts:
• country or diagnostics - DIP switch 1
• country code - DIP switches 2 through 5
• second dial tone (on/off) - DIP switch 6
Figure 15 on page 46 shows the Config DIP switch layout.
Caution: Country configuration is read by the firmware upon power up or
restart. Changing the country, while the R2MFC MBM is operating, causes the
firmware to restart automatically after a delay of five seconds from the last DIP
switch change. All active calls during the restart are dropped.
- R2MFC Media Bay Module 1
- Trademarks 2
- Enhanced 911 Configuration 3
- Radio-frequency Interference 3
- Hearing Aid Compatibility 4
- Important Safety Instructions 4
- Limited Warranty 7
- Warranty Repair Services 8
- After Warranty Service 8
- Contents 9
- 14 Figures 14
- Tables 16
- Before you begin 17
- How to get help 18
- Preface 19 19
- Acronyms 20
- Chapter 1 21
- Overview 21
- R2MFC MBM faceplate elements 22
- System Status LEDs 23
- Config DIP switches 23
- RS232 port 24
- E1 Status LEDs 24
- Bantam jacks 24
- BNC and RJ-48 connectors 24
- Power connectors 24
- MBM DIP switches 25
- 26 Chapter 1 Overview 26
- Chapter 2 27
- Installation process map 28
- R2MFC MBM setup requirements 29
- Environment checklist 30
- Electrical requirements 30
- Software requirements 30
- Chapter 3 31
- Installing the R2MFC MBM 31
- Installing an R2MFC MBM 32
- Reconnecting the equipment 33
- Removing an R2MFC MBM 35
- Wiring an R2MFC MBM 37
- Chapter 4 41
- Configuring the R2MFC MBM 41
- Physical line characteristics 42
- E1 framing 42
- Line signaling 42
- Register signaling 43
- End of dialing (outgoing) 44
- Disable ANI 44
- Default category 44
- Default subscriber status 44
- Setting Config DIP switches 45
- E1 Framing 47
- Signaling 48
- Turning on second dial tone 52
- Chapter 5 55
- R2MFC MBM maintenance 55
- Clock synchronization 56
- Diagnostic tools 57
- Alarms Measurements 58
- Alarms propagation 59
- Faceplate LEDs 60
- Logs and traces 61
- Error messages 61
- Replacing an R2MFC MBM 62
- Upgrading firmware 63
- Chapter 6 67
- Command Line Interface (CLI) 67
- Accessing the CLI 68
- Commands 69
- LOad directory 69
- INfo directory 69
- VIew directory 70
- CNtrl directory 71
- COnfig directory 73
- ALarm directory 75
- SWerr directory 77
- MFC directory 78
- R2 directory 81
- PRI directory 83
- Appendix A 85
- Country code defaults 87
- MFC register signaling 88
- Mexico Config 2 89
- Brazil Config 1 92
- Brazil Config 2 94
- Argentina Config 1 96
- N0027684 01 100
- Appendix B 101
- Appendix C 103
- MFC Signal Definitions 103
- 104 MFC Signal Definitions 104
- Appendix D 105
- CLI Cable Pinout 105
- 106 CLI Cable Pinout 106
MasterCraft manuales
La lista de dispositivos de MasterCraft contiene 28 manuales de usuario y guías para 19 modelos en 14 tipo de dispositivos
Comentarios a estos manuales