Avaya R2MFC Guía de configuración Pagina 22
- Pagina / 106
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
22 Chapter 1 Overview
N0027684 01
External link configuration is performed using the DIP switches on the front of the R2MFC MBM
or by using the CLI, which is accessed through a serial port on the faceplate of the R2MFC MBM.
Internal link configuration is performed using Unified Manager. Refer to “Configuring the
R2MFC MBM” on page 41 for information on how to use the configuration tools.
R2MFC MBM faceplate elements
The faceplate of the R2MFC MBM consists of the following elements:
• “System Status LEDs” on page 23
• “Config DIP switches” on page 23
• “RS232 port” on page 24
• “E1 Status LEDs” on page 24
• “Bantam jacks” on page 24
• “BNC and RJ-48 connectors” on page 24
Figure 2 illustrates the placement of these elements.
Figure 2 R2MFC MBM faceplate
120 Ω E1
RJ-48
75 Ω E1 BNC
Bantam
jacks
E1 status
4 LEDS
RJ-45
DIP
switches
MBM status
3 LEDS
- R2MFC Media Bay Module 1
- Trademarks 2
- Enhanced 911 Configuration 3
- Radio-frequency Interference 3
- Hearing Aid Compatibility 4
- Important Safety Instructions 4
- Limited Warranty 7
- Warranty Repair Services 8
- After Warranty Service 8
- Contents 9
- 14 Figures 14
- Tables 16
- Before you begin 17
- How to get help 18
- Preface 19 19
- Acronyms 20
- Chapter 1 21
- Overview 21
- R2MFC MBM faceplate elements 22
- System Status LEDs 23
- Config DIP switches 23
- RS232 port 24
- E1 Status LEDs 24
- Bantam jacks 24
- BNC and RJ-48 connectors 24
- Power connectors 24
- MBM DIP switches 25
- 26 Chapter 1 Overview 26
- Chapter 2 27
- Installation process map 28
- R2MFC MBM setup requirements 29
- Environment checklist 30
- Electrical requirements 30
- Software requirements 30
- Chapter 3 31
- Installing the R2MFC MBM 31
- Installing an R2MFC MBM 32
- Reconnecting the equipment 33
- Removing an R2MFC MBM 35
- Wiring an R2MFC MBM 37
- Chapter 4 41
- Configuring the R2MFC MBM 41
- Physical line characteristics 42
- E1 framing 42
- Line signaling 42
- Register signaling 43
- End of dialing (outgoing) 44
- Disable ANI 44
- Default category 44
- Default subscriber status 44
- Setting Config DIP switches 45
- E1 Framing 47
- Signaling 48
- Turning on second dial tone 52
- Chapter 5 55
- R2MFC MBM maintenance 55
- Clock synchronization 56
- Diagnostic tools 57
- Alarms Measurements 58
- Alarms propagation 59
- Faceplate LEDs 60
- Logs and traces 61
- Error messages 61
- Replacing an R2MFC MBM 62
- Upgrading firmware 63
- Chapter 6 67
- Command Line Interface (CLI) 67
- Accessing the CLI 68
- Commands 69
- LOad directory 69
- INfo directory 69
- VIew directory 70
- CNtrl directory 71
- COnfig directory 73
- ALarm directory 75
- SWerr directory 77
- MFC directory 78
- R2 directory 81
- PRI directory 83
- Appendix A 85
- Country code defaults 87
- MFC register signaling 88
- Mexico Config 2 89
- Brazil Config 1 92
- Brazil Config 2 94
- Argentina Config 1 96
- N0027684 01 100
- Appendix B 101
- Appendix C 103
- MFC Signal Definitions 103
- 104 MFC Signal Definitions 104
- Appendix D 105
- CLI Cable Pinout 105
- 106 CLI Cable Pinout 106
Sony NW-E013 manuales
Manuales del propietario y guías del usuario para Accesorios de procesador / mezclador de alimentos Sony NW-E013.
Ofrecemos 1 manuales en pdf Sony NW-E013 para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales