Avaya R2MFC Guía de configuración Pagina 70
- Pagina / 106
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
70 Chapter 6 Command Line Interface (CLI)
N0027684 01
VIew directory
Table 18 includes the CLI commands to display the setup parameters. The commands are accessed
from the VIew directory.
Table 18 VIew directory CLI commands
CLI command Description
LNst Displays the status of both links.
ChSt <chan1> <chan2> Displays the status of the channels in the given range.
Where:
chan1 is the lower limit of the range.
chan2 is the upper limit of the range.
The values for chan1 and chan2 are 1...15, 17...31.
ChDt <chan> Prints the channel data.
Where:
chan is the channel number in the range of 1...15, 17...31.
ChDtGrp Prints data for a range of channels.
TT <num> Prints the timer table that contains the timer values in milliseconds.
Where:
num is either 1 (Outgoing timers) or 2 (Incoming timers).
If you do not enter a value for num, all timers are printed.
MR <mfc_link_no> <num> Displays the MFC/R2 generic parameters for each link.
Where:
mfc_link_no is the value of the MFC link number, either 0 or 1.
num is 0 (R2 signals), 1 (MFC Tx signals), or 2 (MFC Rx signals).
If you do not enter a value for num, all MFC/R2 signals are printed.
- R2MFC Media Bay Module 1
- Trademarks 2
- Enhanced 911 Configuration 3
- Radio-frequency Interference 3
- Hearing Aid Compatibility 4
- Important Safety Instructions 4
- Limited Warranty 7
- Warranty Repair Services 8
- After Warranty Service 8
- Contents 9
- 14 Figures 14
- Tables 16
- Before you begin 17
- How to get help 18
- Preface 19 19
- Acronyms 20
- Chapter 1 21
- Overview 21
- R2MFC MBM faceplate elements 22
- System Status LEDs 23
- Config DIP switches 23
- RS232 port 24
- E1 Status LEDs 24
- Bantam jacks 24
- BNC and RJ-48 connectors 24
- Power connectors 24
- MBM DIP switches 25
- 26 Chapter 1 Overview 26
- Chapter 2 27
- Installation process map 28
- R2MFC MBM setup requirements 29
- Environment checklist 30
- Electrical requirements 30
- Software requirements 30
- Chapter 3 31
- Installing the R2MFC MBM 31
- Installing an R2MFC MBM 32
- Reconnecting the equipment 33
- Removing an R2MFC MBM 35
- Wiring an R2MFC MBM 37
- Chapter 4 41
- Configuring the R2MFC MBM 41
- Physical line characteristics 42
- E1 framing 42
- Line signaling 42
- Register signaling 43
- End of dialing (outgoing) 44
- Disable ANI 44
- Default category 44
- Default subscriber status 44
- Setting Config DIP switches 45
- E1 Framing 47
- Signaling 48
- Turning on second dial tone 52
- Chapter 5 55
- R2MFC MBM maintenance 55
- Clock synchronization 56
- Diagnostic tools 57
- Alarms Measurements 58
- Alarms propagation 59
- Faceplate LEDs 60
- Logs and traces 61
- Error messages 61
- Replacing an R2MFC MBM 62
- Upgrading firmware 63
- Chapter 6 67
- Command Line Interface (CLI) 67
- Accessing the CLI 68
- Commands 69
- LOad directory 69
- INfo directory 69
- VIew directory 70
- CNtrl directory 71
- COnfig directory 73
- ALarm directory 75
- SWerr directory 77
- MFC directory 78
- R2 directory 81
- PRI directory 83
- Appendix A 85
- Country code defaults 87
- MFC register signaling 88
- Mexico Config 2 89
- Brazil Config 1 92
- Brazil Config 2 94
- Argentina Config 1 96
- N0027684 01 100
- Appendix B 101
- Appendix C 103
- MFC Signal Definitions 103
- 104 MFC Signal Definitions 104
- Appendix D 105
- CLI Cable Pinout 105
- 106 CLI Cable Pinout 106
Sony NW-E013 manuales
Manuales del propietario y guías del usuario para Accesorios de procesador / mezclador de alimentos Sony NW-E013.
Ofrecemos 1 manuales en pdf Sony NW-E013 para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales