Avaya Configuring WAN Line Services Manual de usuario Pagina 87
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring HSSI Services
117021-A Rev. A 5-3
With BofL enabled, the router sends periodic keep-alive messages to the remote
peer. If you enable BofL locally, you must also configure the remote peer to
enable BofL.
Enabling or Disabling BofL
We recommend that you enable BofL for point-to-point connections between Bay
Networks peers. However, you must disable BofL if such a connection occurs
through a wide area transport service such as Frame Relay or SMDS.
You can enable or disable transmission of BofL messages on this interface.
Setting the BofL Interval
This parameter is valid only if BofL is enabled on the interface.
After sending a BofL message, the router starts a timer that has a value equal to
five times the setting of this parameter. If the router does not receive a BofL
message from the remote peer before the timer expires, the router disables the
HSSI circuit, and then attempts to restart it.
Both ends of the point-to-point connection must be configured with the same
interval value.
Set the BofL interval to a value from 1 to 60 seconds.
Setting the MTU
The default buffer size, or maximum transmission unit (MTU), determines the
largest frame that can travel across the HSSI interface.
The default value is 4608 bytes. Specify a MTU ffrom 3 to 4608 bytes on this
interface.
Site Manager: BofL parameter: page A-12
Site Manager: BofL Frequency parameter: page A-13
Site Manager: MTU parameter: page A-13
- Configuring WAN 1
- Line Services 1
- USA Requirements Only 3
- Canada Requirements Only 5
- T1 Service 8
- Bay Networks Software License 9
- (continued) 10
- Contents 11
- About This Guide 23
- Before You Begin 24
- Conventions 24
- Acronyms 25
- For More Information 28
- Chapter 1 29
- Getting Started 29
- 1-2 117021-A Rev. A 30
- 1-4 117021-A Rev. A 32
- Configuring ATM Services 33
- Token Ring Services 33
- Chapter 2 35
- 2-2 117021-A Rev. A 36
- 117021-A Rev. A 2-3 37
- 2-4 117021-A Rev. A 38
- Setting the BofL Timeout 39
- Setting the MTU 39
- Configuring Clocking Signals 40
- 117021-A Rev. A 2-7 41
- Setting the Signal Mode 42
- 117021-A Rev. A 2-9 43
- Setting Minimum Frame Spacing 44
- 117021-A Rev. A 2-11 45
- 2-12 117021-A Rev. A 46
- Setting the CRC Size 47
- Setting the Signaling Method 48
- Setting the Line Coding 49
- Configuring KG84A Security 50
- 117021-A Rev. A 2-17 51
- 2-18 117021-A Rev. A 52
- Setting the Retry Count 53
- Setting the Link Idle Timer 53
- Setting the Cable Type 54
- Setting the Retry Timer 55
- Setting the Hold Down Time 56
- Setting a Priority 56
- 117021-A Rev. A 2-23 57
- Setting the IFTF Pattern 58
- 117021-A Rev. A 2-25 59
- 117021-A Rev. A 2-27 61
- Setting the Station Type 62
- Setting the Control Field 62
- Setting the Window Size 63
- Setting the N2 Retry Count 63
- 2-30 117021-A Rev. A 64
- Setting the Link Setup Action 65
- Viewing the WAN Protocol 66
- Chapter 3 67
- Asynchronous Services 67
- 3-2 117021-A Rev. A 68
- Setting the Baud Rate 69
- Setting the Idle Timer 69
- 3-4 117021-A Rev. A 70
- Setting the Remote IP Address 71
- Specifying the Remote Port 71
- Specifying the Local Port 71
- 3-6 117021-A Rev. A 72
- 117021-A Rev. A 3-7 73
- Chapter 4 75
- 4-2 117021-A Rev. A 76
- 2. Click on Edit DSU/CSU 76
- Setting the Option Mode 77
- 4-4 117021-A Rev. A 78
- 117021-A Rev. A 4-5 79
- 4-6 117021-A Rev. A 80
- Loopback Test Modes 81
- 4-8 117021-A Rev. A 82
- Figure 4-7. Analog Loopback 82
- Figure 4-8. Pattern-2047 Test 83
- Chapter 5 85
- Configuring HSSI Services 85
- Configuring BofL Messages 86
- 5-4 117021-A Rev. A 88
- Chapter 6 91
- Configuring E1 or T1 Services 91
- 6-2 117021-A Rev. A 92
- Setting the T1 Frame Type 93
- 6-4 117021-A Rev. A 94
- Figure 6-2. Bipolar Format 94
- Specifying Line Buildout 95
- Editing E1 Services 97
- 6-8 117021-A Rev. A 98
- Setting the Clock Source 99
- Assigning Channel Functions 100
- Chapter 7 101
- About MCE1 and MCT1 Services 102
- 117021-A Rev. A 7-3 103
- Setting the Clock Parameters 104
- 7-6 117021-A Rev. A 106
- 4. Click on OK 106
- 5. Continue with 106
- Configuring WAN Line Services 106
- 117021-A Rev. A 7-7 107
- 7-8 117021-A Rev. A 108
- 117021-A Rev. A 7-9 109
- 7-10 117021-A Rev. A 110
- 117021-A Rev. A 7-11 111
- 7-12 117021-A Rev. A 112
- 117021-A Rev. A 7-13 113
- 7-14 117021-A Rev. A 114
- 117021-A Rev. A 7-15 115
- Configuring a DS0A Connection 116
- 117021-A Rev. A 7-17 117
- BYS0060A 117
- 117021-A Rev. A 118
- Defining Logical Lines 119
- Click on Add 120
- 117021-A Rev. A 7-21 121
- Chapter 8 123
- 7-24 117021-A Rev. A 124
- 3. Click on Apply 124
- 117021-A Rev. A 7-25 125
- 7-26 117021-A Rev. A 126
- 117021-A Rev. A 7-27 127
- 7-28 117021-A Rev. A 128
- 117021-A Rev. A 7-29 129
- 7-30 117021-A Rev. A 130
- Assigning Timeslots 131
- 7-32 117021-A Rev. A 132
- 117021-A Rev. A 7-33 133
- 7-34 117021-A Rev. A 134
- 117021-A Rev. A 7-35 135
- Testing MCE1 and MCT1 Lines 136
- Setting Port Test Parameters 137
- 7-38 117021-A Rev. A 138
- 117021-A Rev. A 7-39 139
- Running Port Tests 140
- 117021-A Rev. A 7-43 143
- Running Logical Line Tests 144
- Click on Done 145
- Configuring Multiline Services 147
- 8-2 117021-A Rev. A 148
- Multiline Example 149
- Software Considerations 150
- 117021-A Rev. A 8-7 153
- 8-8 117021-A Rev. A 154
- 117021-A Rev. A 8-9 155
- 8-10 117021-A Rev. A 156
- 117021-A Rev. A 8-11 157
- 117021-A Rev. A 8-13 159
- 8-14 117021-A Rev. A 160
- 117021-A Rev. A 8-15 161
- Appendix A 163
- Asynchronous Line Parameters 164
- 117021-A Rev. A A-3 165
- A-4 117021-A Rev. A 166
- 117021-A Rev. A A-5 167
- A-6 117021-A Rev. A 168
- DSU/CSU Parameters 169
- 170
- 170
- E1 Line Parameters 171
- 172
- 172
- 173
- HSSI Line Parameters 174
- 117021-A Rev. A A-13 175
- A-14 117021-A Rev. A 176
- 177
- LAPB Parameters 178
- 179
- A-18 117021-A Rev. A 180
- 117021-A Rev. A A-19 181
- 182
- 117021-A Rev. A A-21 183
- A-22 117021-A Rev. A 184
- MCE1 Port Parameters 185
- 186
- 188
- 117021-A Rev. A A-27 189
- MCT1 Port Parameters 190
- 117021-A Rev. A A-29 191
- A-30 117021-A Rev. A 192
- 193
- 195
- 197
- 199
- 201
- Synchronous Line Parameters 204
- 207
- 207
- 208
- 209
- A-48 117021-A Rev. A 210
- A-50 117021-A Rev. A 212
- 117021-A Rev. A A-51 213
- 117021-A Rev. A A-53 215
- A-54 117021-A Rev. A 216
- 218
- 218
- 219
- 220
- 221
- T1 Line Parameters 222
- 223
- 225
- A-64 117021-A Rev. A 226
- Appendix B 227
- B-2 117021-A Rev. A 228
- MCE1 Line Parameters 230
- MCT1 Line Parameters 232
- B-8 117021-A Rev. A 234
- B-10 117021-A Rev. A 236
- Multiline Parameters 237
- Glossary 239
- 117021-A Rev. A Index-1 241
- 117021-A Rev. A Index-3 243
- 117021-A Rev. A Index-5 245
Relacionado con productos y manuales para Redes Avaya Configuring WAN Line Services
Redes Avaya R2 Guía de instalación
(147 paginas)
(147 paginas)
Redes Avaya BayRS, BCC, and Site Manager Software Version 15.1.0.0 Fixed Anomalies Manual de usuario
(26 paginas)
(26 paginas)
Redes Avaya Configuring ATM Services Manual de usuario
(262 paginas)
(262 paginas)
Redes Avaya BayRs Version 12.20 aviso
(54 paginas)
(54 paginas)
Redes Avaya BCM50 Guía para resolver problemas
(92 paginas)
(92 paginas)
Redes Avaya DHCP BCM Rls 6.0 Manual de usuario
(26 paginas)
(26 paginas)
Redes Avaya E1/FE1 Manual de usuario
(42 paginas)
(42 paginas)
Redes Avaya v8.0 Manual de usuario
(23 paginas)
(23 paginas)
Redes Avaya Configuring Line Services Manual de usuario
(268 paginas)
(268 paginas)
Redes Avaya E1 Manual de usuario
(52 paginas)
(52 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.367 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales