Avaya Configuring WAN Line Services Manual de usuario Pagina 112
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring WAN Line Services
7-12 117021-A Rev. A
Set the line coding for this MCT1 interface.
Setting the Signal Level
The Signal Level parameter specifies the T1 transmit power level in decibels (dB).
Line buildout conditions the signals to mitigate attenuation, and depends on the
physical length of the T1 line.
The carrier determines signal levels on a long-haul (0 to 6000 ft. of cable) T1
network interface. Signal power for digital cross-connect (DSX-1) short-haul (0
to 655 ft.) is based on cable length.
For DSX-1, decibel levels correlate with cable length, as follows:
• 0.0 dB -- 0 to 133 ft.
• 0.5 dB -- 133 to 255 ft.
• 0.8 dB -- 266 to 399 ft.
• 1.1 dB -- 399 to 533 ft.
• 1.5 dB -- 533 to 655 ft.
By default, the signal level is set to 0.0 dB. If 0.0 dB is not sufficient for
long-haul, the carrier determines values of -15 and -7.5 dB. Set the long-haul or
short-haul signal level for this MCT1 interface.
Setting the Alarm Threshold Time
By default, the MCT1 interface waits 2 seconds before logging a performance
defect or anomaly as an event message. Change that time to any value from 2 to
10 seconds.
Set the alarm threshold for this MCT1 interface.
Site Manager: Line Coding parameter: page A-28
Site Manager: Signal Level (dB) parameter: page A-29
Site Manager: Setup Alarm Threshold (seconds) parameter: page A-29
- Configuring WAN 1
- Line Services 1
- USA Requirements Only 3
- Canada Requirements Only 5
- T1 Service 8
- Bay Networks Software License 9
- (continued) 10
- Contents 11
- About This Guide 23
- Before You Begin 24
- Conventions 24
- Acronyms 25
- For More Information 28
- Chapter 1 29
- Getting Started 29
- 1-2 117021-A Rev. A 30
- 1-4 117021-A Rev. A 32
- Configuring ATM Services 33
- Token Ring Services 33
- Chapter 2 35
- 2-2 117021-A Rev. A 36
- 117021-A Rev. A 2-3 37
- 2-4 117021-A Rev. A 38
- Setting the BofL Timeout 39
- Setting the MTU 39
- Configuring Clocking Signals 40
- 117021-A Rev. A 2-7 41
- Setting the Signal Mode 42
- 117021-A Rev. A 2-9 43
- Setting Minimum Frame Spacing 44
- 117021-A Rev. A 2-11 45
- 2-12 117021-A Rev. A 46
- Setting the CRC Size 47
- Setting the Signaling Method 48
- Setting the Line Coding 49
- Configuring KG84A Security 50
- 117021-A Rev. A 2-17 51
- 2-18 117021-A Rev. A 52
- Setting the Retry Count 53
- Setting the Link Idle Timer 53
- Setting the Cable Type 54
- Setting the Retry Timer 55
- Setting the Hold Down Time 56
- Setting a Priority 56
- 117021-A Rev. A 2-23 57
- Setting the IFTF Pattern 58
- 117021-A Rev. A 2-25 59
- 117021-A Rev. A 2-27 61
- Setting the Station Type 62
- Setting the Control Field 62
- Setting the Window Size 63
- Setting the N2 Retry Count 63
- 2-30 117021-A Rev. A 64
- Setting the Link Setup Action 65
- Viewing the WAN Protocol 66
- Chapter 3 67
- Asynchronous Services 67
- 3-2 117021-A Rev. A 68
- Setting the Baud Rate 69
- Setting the Idle Timer 69
- 3-4 117021-A Rev. A 70
- Setting the Remote IP Address 71
- Specifying the Remote Port 71
- Specifying the Local Port 71
- 3-6 117021-A Rev. A 72
- 117021-A Rev. A 3-7 73
- Chapter 4 75
- 4-2 117021-A Rev. A 76
- 2. Click on Edit DSU/CSU 76
- Setting the Option Mode 77
- 4-4 117021-A Rev. A 78
- 117021-A Rev. A 4-5 79
- 4-6 117021-A Rev. A 80
- Loopback Test Modes 81
- 4-8 117021-A Rev. A 82
- Figure 4-7. Analog Loopback 82
- Figure 4-8. Pattern-2047 Test 83
- Chapter 5 85
- Configuring HSSI Services 85
- Configuring BofL Messages 86
- 5-4 117021-A Rev. A 88
- Chapter 6 91
- Configuring E1 or T1 Services 91
- 6-2 117021-A Rev. A 92
- Setting the T1 Frame Type 93
- 6-4 117021-A Rev. A 94
- Figure 6-2. Bipolar Format 94
- Specifying Line Buildout 95
- Editing E1 Services 97
- 6-8 117021-A Rev. A 98
- Setting the Clock Source 99
- Assigning Channel Functions 100
- Chapter 7 101
- About MCE1 and MCT1 Services 102
- 117021-A Rev. A 7-3 103
- Setting the Clock Parameters 104
- 7-6 117021-A Rev. A 106
- 4. Click on OK 106
- 5. Continue with 106
- Configuring WAN Line Services 106
- 117021-A Rev. A 7-7 107
- 7-8 117021-A Rev. A 108
- 117021-A Rev. A 7-9 109
- 7-10 117021-A Rev. A 110
- 117021-A Rev. A 7-11 111
- 7-12 117021-A Rev. A 112
- 117021-A Rev. A 7-13 113
- 7-14 117021-A Rev. A 114
- 117021-A Rev. A 7-15 115
- Configuring a DS0A Connection 116
- 117021-A Rev. A 7-17 117
- BYS0060A 117
- 117021-A Rev. A 118
- Defining Logical Lines 119
- Click on Add 120
- 117021-A Rev. A 7-21 121
- Chapter 8 123
- 7-24 117021-A Rev. A 124
- 3. Click on Apply 124
- 117021-A Rev. A 7-25 125
- 7-26 117021-A Rev. A 126
- 117021-A Rev. A 7-27 127
- 7-28 117021-A Rev. A 128
- 117021-A Rev. A 7-29 129
- 7-30 117021-A Rev. A 130
- Assigning Timeslots 131
- 7-32 117021-A Rev. A 132
- 117021-A Rev. A 7-33 133
- 7-34 117021-A Rev. A 134
- 117021-A Rev. A 7-35 135
- Testing MCE1 and MCT1 Lines 136
- Setting Port Test Parameters 137
- 7-38 117021-A Rev. A 138
- 117021-A Rev. A 7-39 139
- Running Port Tests 140
- 117021-A Rev. A 7-43 143
- Running Logical Line Tests 144
- Click on Done 145
- Configuring Multiline Services 147
- 8-2 117021-A Rev. A 148
- Multiline Example 149
- Software Considerations 150
- 117021-A Rev. A 8-7 153
- 8-8 117021-A Rev. A 154
- 117021-A Rev. A 8-9 155
- 8-10 117021-A Rev. A 156
- 117021-A Rev. A 8-11 157
- 117021-A Rev. A 8-13 159
- 8-14 117021-A Rev. A 160
- 117021-A Rev. A 8-15 161
- Appendix A 163
- Asynchronous Line Parameters 164
- 117021-A Rev. A A-3 165
- A-4 117021-A Rev. A 166
- 117021-A Rev. A A-5 167
- A-6 117021-A Rev. A 168
- DSU/CSU Parameters 169
- 170
- 170
- E1 Line Parameters 171
- 172
- 172
- 173
- HSSI Line Parameters 174
- 117021-A Rev. A A-13 175
- A-14 117021-A Rev. A 176
- 177
- LAPB Parameters 178
- 179
- A-18 117021-A Rev. A 180
- 117021-A Rev. A A-19 181
- 182
- 117021-A Rev. A A-21 183
- A-22 117021-A Rev. A 184
- MCE1 Port Parameters 185
- 186
- 188
- 117021-A Rev. A A-27 189
- MCT1 Port Parameters 190
- 117021-A Rev. A A-29 191
- A-30 117021-A Rev. A 192
- 193
- 195
- 197
- 199
- 201
- Synchronous Line Parameters 204
- 207
- 207
- 208
- 209
- A-48 117021-A Rev. A 210
- A-50 117021-A Rev. A 212
- 117021-A Rev. A A-51 213
- 117021-A Rev. A A-53 215
- A-54 117021-A Rev. A 216
- 218
- 218
- 219
- 220
- 221
- T1 Line Parameters 222
- 223
- 225
- A-64 117021-A Rev. A 226
- Appendix B 227
- B-2 117021-A Rev. A 228
- MCE1 Line Parameters 230
- MCT1 Line Parameters 232
- B-8 117021-A Rev. A 234
- B-10 117021-A Rev. A 236
- Multiline Parameters 237
- Glossary 239
- 117021-A Rev. A Index-1 241
- 117021-A Rev. A Index-3 243
- 117021-A Rev. A Index-5 245
Relacionado con productos y manuales para Redes Avaya Configuring WAN Line Services
Redes Avaya R2 Guía de instalación
(147 paginas)
(147 paginas)
Redes Avaya BayRS, BCC, and Site Manager Software Version 15.1.0.0 Fixed Anomalies Manual de usuario
(26 paginas)
(26 paginas)
Redes Avaya Configuring ATM Services Manual de usuario
(262 paginas)
(262 paginas)
Redes Avaya BayRs Version 12.20 aviso
(54 paginas)
(54 paginas)
Redes Avaya BCM50 Guía para resolver problemas
(92 paginas)
(92 paginas)
Redes Avaya DHCP BCM Rls 6.0 Manual de usuario
(26 paginas)
(26 paginas)
Redes Avaya E1/FE1 Manual de usuario
(42 paginas)
(42 paginas)
Redes Avaya v8.0 Manual de usuario
(23 paginas)
(23 paginas)
Redes Avaya Configuring Line Services Manual de usuario
(268 paginas)
(268 paginas)
Redes Avaya E1 Manual de usuario
(52 paginas)
(52 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.152 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales