Avaya Configuring ATM Services Manual de usuario Pagina 54
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring ATM Services
2-14 114056 Rev. A
Of the different methods, having multiple PVCs per service record uses network
addressing most efficiently, and is the easiest to configure.
Although you need to configure each PVC manually, you need only define and
associate protocols with the ATM network service record. All the PVCs that you
configure for a given ATM service record carry the protocols that you select and
configure to run on that service record.
Multiple PVCs per service record works best in either fully meshed environments
or in nonmeshed environments where systems not directly connected to each other
have no need to communicate. You can configure multiple PVCs per service
record as long as you do not need to separate protocols by PVC (that is, all PVCs
accept the same protocols).
There are, however, ways to configure upper-layer protocols, such as IP or
Internet Packet Exchange (IPX), to allow systems in nonmeshed networks to fully
communicate. See the documentation for these upper-layer protocols for more
information.
One PVC
One PVC per service record works the same way as multiple PVCs per service
record, except that you assign only one PVC per service record. When you define
only one PVC per service record, upper-layer protocols treat the ATM network as
a series of direct, point-to-point connections, viewing each PVC as an individual
network interface.
You can, therefore, configure each PVC with different protocols and parameter
settings. This allows you to connect to different network sites using, for example,
different types of data encapsulation (Figure 2-7).
Note: When you configure multiple PVCs per service record, the PVCs all use
the data encapsulation type that you set for the ATM service record (that is, the
value of the Data Encapsulation Type parameter set in the ATM Service
Records List window). Refer to “Data Encapsulation,” earlier in this chapter,
for more information.
- Configuring ATM 1
- Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- 114056 Rev. A 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- World Wide Web 27
- Customer Service FTP 27
- Support Source CD 28
- CompuServe 28
- InfoFACTS 29
- How to Get Help 29
- Chapter 1 31
- Starting ATM 31
- Adding ATM to the Router 32
- Defining a Service Record 33
- 114056 Rev. A 1-5 35
- Supported Protocols 36
- Adding PVCs 38
- Chapter 2 41
- Understanding ATM Concepts 41
- 2-2 114056 Rev. A 42
- Figure 2-2. ATM Cell Header 42
- Data Transmission 43
- VP = Virtual path 44
- VC = Virtual channel 44
- Physical Layer 45
- ATM Layer 46
- ATM Adaptation Layer (AAL5) 47
- 2-8 114056 Rev. A 48
- Data Encapsulation 49
- 2-10 114056 Rev. A 50
- Encapsulation Rules for PVCs 52
- PVC Access Methods 53
- 2-14 114056 Rev. A 54
- Hybrid Access 55
- 2-16 114056 Rev. A 56
- Figure 2-8. Hybrid PVCs 56
- SVC Access Methods 58
- ATM Traffic Parameters 58
- Variable Bit Rate 59
- Available Bit Rate 59
- Rules for Editing Protocols 60
- ARP and Inverse ARP Support 60
- ATM Error Checking 61
- Converting Mb/s to Cells/s 61
- Example of an ATM Network 62
- Hardware Devices 64
- 2-26 114056 Rev. A 66
- For More Information 68
- Chapter 3 71
- 3-2 114056 Rev. A 72
- ATM Address Resolution 73
- 3-4 114056 Rev. A 74
- 114056 Rev. A 3-5 75
- Chapter 4 77
- LAN Emulation Components 78
- LAN Emulation Server 79
- Broadcast and Unknown Server 79
- 4-4 114056 Rev. A 80
- Initial State 81
- LECS Connect State 81
- Configure State 81
- Join State 81
- Initial Registration State 82
- BUS Connect State 82
- Operational State 82
- Chapter 5 85
- Customizing an ATM Line 85
- 5-2 114056 Rev. A 86
- Assigning the Framing Mode 87
- Defining ATM Cell Insertion 88
- Defining the Interface MTU 89
- 5-6 114056 Rev. A 90
- Specifying DS3 Line Build Out 92
- Chapter 6 95
- Service Records 95
- Autogenerating ATM Addresses 96
- Assigning ATM Addresses 97
- 6-4 114056 Rev. A 98
- Entering an Emulated LAN Name 100
- Defining an Emulated LAN Type 100
- Defining the MTU 101
- Where to Go Next 102
- Chapter 7 103
- Customizing PVCs 103
- Setting a VCI Number 104
- Setting the PCR 105
- Configuring ATM Services 106
- 7-4 114056 Rev. A 106
- Table 7-1. Valid PCR Ranges 106
- Setting the SCR 107
- 7-6 114056 Rev. A 108
- Table 7-2. Valid SCR Ranges 108
- Setting the MBS 109
- Setting the Transmit SDU Size 110
- Setting the Receive SDU Size 110
- Chapter 8 113
- Specifying an Owner 114
- Entering an ELAN Name 114
- Entering a LES ATM Address 114
- Selecting a Configuration Mode 115
- 8-4 114056 Rev. A 116
- Setting the Control Timeout 117
- Setting the Aging Time 118
- 114056 Rev. A 8-7 119
- Setting the Flush Timeout 120
- Entering a LECS ATM Address 121
- Chapter 9 123
- Customizing Signaling 123
- Assigning a Protocol Standard 124
- Setting Connection Thresholds 125
- Setting Signaling Timers 126
- 9-6 114056 Rev. A 128
- 9-8 114056 Rev. A 130
- Defining Retransmissions 131
- Pacing Calls 131
- Chapter 10 133
- Customizing ILMI 133
- Setting the ILMI Get Timer 134
- Setting the ILMI Set Timer 135
- Chapter 11 137
- Changing the ILMI VPI Number 138
- Changing the ILMI VCI Number 138
- Table 11-1. Valid PCR Ranges 139
- Table 11-2. Valid SCR Ranges 141
- Chapter 12 145
- Customizing SAAL 145
- Enabling or Disabling SAAL 146
- Modifying SAAL Timers 146
- Defining PDU Values 148
- Appendix A 151
- Site Manager Parameters 151
- A-2 114056 Rev. A 152
- Using the Menu Path 153
- A-4 114056 Rev. A 154
- 155
- 158
- 162
- A-14 114056 Rev. A 164
- A-18 114056 Rev. A 168
- 170
- A-22 114056 Rev. A 172
- 174
- A-26 114056 Rev. A 176
- A-28 114056 Rev. A 178
- A-30 114056 Rev. A 180
- 181
- 182
- A-34 114056 Rev. A 184
- A-38 114056 Rev. A 188
- A-40 114056 Rev. A 190
- 191
- A-42 114056 Rev. A 192
- A-44 114056 Rev. A 194
- A-46 114056 Rev. A 196
- A-48 114056 Rev. A 198
- A-50 114056 Rev. A 200
- ILMI category 202
- A-54 114056 Rev. A 204
- A-56 114056 Rev. A 206
- A-58 114056 Rev. A 208
- A-60 114056 Rev. A 210
- 212
- A-64 114056 Rev. A 214
- 216
- A-68 114056 Rev. A 218
- A-70 114056 Rev. A 220
- Appendix B 221
- B-2 114056 Rev. A 222
- ATM FRE2 Line Parameters 224
- ATM ARE Line Parameters 224
- (continued) 225
- B-6 114056 Rev. A 226
- Appendix C 229
- ATM Sample Log 229
- C-2 114056 Rev. A 230
- C-4 114056 Rev. A 232
- C-6 114056 Rev. A 234
- C-8 114056 Rev. A 236
- C-10 114056 Rev. A 238
- C-12 114056 Rev. A 240
- C-14 114056 Rev. A 242
- C-16 114056 Rev. A 244
- C-18 114056 Rev. A 246
- C-20 114056 Rev. A 248
- C-22 114056 Rev. A 250
- C-24 114056 Rev. A 252
- C-26 114056 Rev. A 254
- 114056 Rev. A Index-1 257
- 114056 Rev. A Index-3 259
- 114056 Rev. A Index-5 261
- 114056 Rev. A Index-7 263
- 114056 Rev. A Index-9 265
- 114056 Rev. A Index-11 267
Relacionado con productos y manuales para Redes Avaya Configuring ATM Services
Redes Avaya Configuring APPN Services Manual de usuario
(150 paginas)
(150 paginas)
Redes Avaya R1.3 Guía de configuración
(13 paginas)
(13 paginas)
Redes Avaya T1/E1 Manual de usuario
(24 paginas)
(24 paginas)
Redes Avaya BayRS, BCC, and Site Manager Software Version 15.0.0.0 Fixed Anomalies Manual de usuario
(30 paginas)
(30 paginas)
Redes Avaya X.25 Manual de usuario
(272 paginas)
(272 paginas)
Redes Avaya Attendant Console Manual de usuario
(62 paginas)
(62 paginas)
Redes Avaya BCM200/400 Manual de instalación
(374 paginas)
(374 paginas)
Redes Avaya Configuring PPP Services Manual de usuario
(150 paginas)
(150 paginas)
Redes Avaya Configuring Line Services Manual de usuario
(301 paginas)
(301 paginas)
Redes Avaya Configuring ATM Services Manual de usuario
(310 paginas)
(310 paginas)
Redes Avaya BCM First Time Guía de instalación
(14 paginas)
(14 paginas)
Redes Avaya IPv6 Manual de usuario
(162 paginas)
(162 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales