Avaya Connecting BayStack AN and ANH Platforms to a Network Manual de usuario Pagina 91
- Pagina / 178
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
114074 Rev. A 5-1
Chapter 5
Configuring an Access Node as a
Network Boot Client
To enable an AN or ANH for Netboot or Directed Netboot, you configure one or
more router interfaces for network booting. You can do this using a Site Manager
remote connection (as described in
Chapter 4) or at the AN/ANH local console
using Technician Interface commands. This chapter describes how to use the
•
ifconfig command to configure the AN/ANH’s initial IP interface to the
network
•
bconfig command to specify the location and name of a software image and
configuration file
Working with a Person at the AN/ANH Site
Written for a person at the AN/ANH site, Installing and Operating BayStack AN
and ANH Systems provides instructions for setting up the router for each of the
boot options. These instructions assume that a network administrator provides the
person at the AN/ANH site with the appropriate
ifconfig and bconfig commands.
To Configure This Boot Method Complete These Sections
Netboot or Directed Netboot over a
synchronous interface
“Configuring the Router Boot Source” and
“
Configuring an IP Synchronous Interface for
Network Booting”
Netboot or Directed Netboot over an
Ethernet interface
“
Configuring the Router Boot Source” and
“
Configuring an Ethernet Interface for Network
Booting”
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- 114074 Rev. A vii 7
- 114074 Rev. A ix 9
- 114074 Rev. A 10
- 114074 Rev. A xi 11
- 114074 Rev. A xiii 13
- About This Guide 15
- Before You Begin 16
- Conventions 17
- Acronyms 18
- 114074 Rev. A xix 19
- 114074 Rev. A xxi 21
- Bay Networks Customer Service 22
- World Wide Web 23
- Customer Service FTP 23
- Support Source CD 24
- CompuServe 24
- InfoFACTS 25
- How to Get Help 25
- Chapter 1 27
- 1-2 114074 Rev. A 28
- ANH Models 29
- 1-4 114074 Rev. A 30
- Access Node Software 31
- Software Management Tools 32
- Router Software 32
- Boot Configuration Options 33
- 1-8 114074 Rev. A 34
- The Boot Process 36
- 114074 Rev. A 1-11 37
- CAN0001A 38
- 114074 Rev. A 1-13 39
- 114074 Rev. A 1-15 41
- Local Boot 42
- CAN0006A 43
- Chapter 2 45
- EZ-Install 46
- Booting the Router Routinely 47
- Directed Netboot 48
- Completing a Startup Option 49
- 114074 Rev. A 2-7 51
- 2-10 114074 Rev. A 54
- Chapter 3 55
- Setting Up a UNIX Boot Server 55
- Setting Up BOOTP Sockets 56
- Setting Up BOOTPD to Run 57
- 3-6 114074 Rev. A 60
- 3-8 114074 Rev. A 62
- Setting Up a TFTP Server 63
- The examples in 64
- 114074 Rev. A 3-11 65
- 3-12 114074 Rev. A 66
- What to Do Next 67
- Chapter 4 69
- Configuring Network Booting 69
- Creating Configuration Files 70
- Preparing an Image 71
- Configuring Network Booting 75
- 4-8 114074 Rev. A 76
- 2. Click on Add 76
- Click on OK 77
- (Figure 4-4) 77
- 79
- 80
- CAN0007A 82
- 114074 Rev. A 4-15 83
- 4-16 114074 Rev. A 84
- 114074 Rev. A 4-17 85
- 4-18 114074 Rev. A 86
- 1. Click on Client I/F 87
- Chapter 5 91
- Network Boot Client 91
- <TFTP host> 92
- (continued) 92
- <TFTP 93
- (continued) 93
- <interface> 94
- <next 94
- <interface> 95
- <IP address> 95
- <subnet mask> 95
- <next hop 95
- 114074 Rev. A 5-8 98
- Chapter 6 99
- 101
- 6-4 114074 Rev. A 102
- 114074 Rev. A 6-5 103
- 6-6 114074 Rev. A 104
- About the N11 DCM 105
- 6-8 114074 Rev. A 106
- Ethernet Statistics Group 107
- Host Group 107
- HostTopN Group 108
- Matrix Group 108
- Filter Group 108
- Packet Capture Group 108
- Enabling the DCM 109
- 111
- 112
- 112
- 113
- 113
- 114
- 114074 Rev. A 6-19 117
- 2. Click on OK 119
- RMON Implementation Notes 121
- RMON Interoperability Issues 121
- 6-24 114074 Rev. A 122
- 114074 Rev. A 6-25 123
- 6-26 114074 Rev. A 124
- 114074 Rev. A 6-27 125
- 6-28 114074 Rev. A 126
- 114074 Rev. A 6-29 127
- Appendix A 129
- Router Fails to Netboot 131
- 114074 Rev. A A-5 133
- <connector> 135
- 114074 Rev. A A-9 137
- Displaying Parameter Settings 138
- 114074 Rev. A A-11 139
- Debugging the BOOTP Server 140
- Table A-1. BOOTP Messages 141
- <IP_address> 143
- Upgrading the Software Image 145
- Restoring a Local File System 145
- Appendix B 147
- Global Information Worksheet 149
- Router Protocol Worksheets 151
- OSPF Worksheet 152
- Wide-Area Protocol Worksheets 154
- Frame Relay Worksheet 155
- PPP Standard Worksheet 156
- CAN0008A 160
- Appendix C 161
- Implementation Notes 161
- C-2 114074 Rev. A 162
- Network Configuration Options 163
- Configuring a Single ANH 164
- 114074 Rev. A C-5 165
- Configuring Multiple Hubs 166
- CAN0010A 167
- C-8 114074 Rev. A 168
- CAN0011A 169
- CAN0012A 170
- 114074 Rev. A Index-1 171
- 114074 Rev. A Index-3 173
- 114074 Rev. A Index-5 175
- 114074 Rev. A Index-7 177
Relacionado con productos y manuales para Software Avaya Connecting BayStack AN and ANH Platforms to a Network
Software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manual de usuario
(148 paginas)
(148 paginas)
Software Avaya Configuring Traffic Filters and Protocol Prioritization Manual de usuario
(162 paginas)
(162 paginas)
Software Avaya Nortel Business Communications Manager 450 1.0 Administration and Security Manual de usuario
(200 paginas)
(200 paginas)
Software Avaya BCM 4.0 Manual de usuario
(398 paginas)
(398 paginas)
Software Avaya Business Communications Manager - Multimedia Contact Center Manual de usuario
(38 paginas)
(38 paginas)
Software Avaya Media Processing Server Series Alarm Reference Manual (Software Release 2.1) Manual de usuario
(452 paginas)
(452 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales