Avaya Connecting BayStack AN and ANH Platforms to a Network Manual de usuario Pagina 153
- Pagina / 178
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Local Boot: The Quick-Start Procedure
114074 Rev. A B-7
Enter decimal value for Router Priority
[1]:
(For Broadcast, NBMA or
Point-to-MultiPoint)
Enter a router priority value. The
lower the value (above zero), the
higher the priority.
Note: If you set the router priority
to zero (0), the router is not eligible
to become the designated router
on this particular network.
Enter decimal value in seconds for Poll
Interval [20]:
(For NBMA only)
Enter the largest number of
seconds allowed between Hello
packets the router sends to an
inactive NBMA neighbor.
The router suggests a 20-second
interval.
Enter IP address of neighbor in dotted
decimal notation or enter q to quit:
(For NBMA only)
Enter addresses for all NBMA
neighbors you want the router to
communicate with.
Enter q and press the Return key
when you finish entering
addresses.
Enter IP address of neighbor in dotted
decimal notation:
(For PPP only)
Enter addresses for the PPP
neighbor you want the router to
communicate with.
Static Route to Site Manager Worksheet
Requested Information Options Your Information
Destination Network [0.0.0.0]: Enter the gateway address of the
destination network. An address
of 0.0.0.0 specifies the default
route.
(continued)
OSPF Worksheet
(continued)
Requested Information Options Your Response
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- 114074 Rev. A vii 7
- 114074 Rev. A ix 9
- 114074 Rev. A 10
- 114074 Rev. A xi 11
- 114074 Rev. A xiii 13
- About This Guide 15
- Before You Begin 16
- Conventions 17
- Acronyms 18
- 114074 Rev. A xix 19
- 114074 Rev. A xxi 21
- Bay Networks Customer Service 22
- World Wide Web 23
- Customer Service FTP 23
- Support Source CD 24
- CompuServe 24
- InfoFACTS 25
- How to Get Help 25
- Chapter 1 27
- 1-2 114074 Rev. A 28
- ANH Models 29
- 1-4 114074 Rev. A 30
- Access Node Software 31
- Software Management Tools 32
- Router Software 32
- Boot Configuration Options 33
- 1-8 114074 Rev. A 34
- The Boot Process 36
- 114074 Rev. A 1-11 37
- CAN0001A 38
- 114074 Rev. A 1-13 39
- 114074 Rev. A 1-15 41
- Local Boot 42
- CAN0006A 43
- Chapter 2 45
- EZ-Install 46
- Booting the Router Routinely 47
- Directed Netboot 48
- Completing a Startup Option 49
- 114074 Rev. A 2-7 51
- 2-10 114074 Rev. A 54
- Chapter 3 55
- Setting Up a UNIX Boot Server 55
- Setting Up BOOTP Sockets 56
- Setting Up BOOTPD to Run 57
- 3-6 114074 Rev. A 60
- 3-8 114074 Rev. A 62
- Setting Up a TFTP Server 63
- The examples in 64
- 114074 Rev. A 3-11 65
- 3-12 114074 Rev. A 66
- What to Do Next 67
- Chapter 4 69
- Configuring Network Booting 69
- Creating Configuration Files 70
- Preparing an Image 71
- Configuring Network Booting 75
- 4-8 114074 Rev. A 76
- 2. Click on Add 76
- Click on OK 77
- (Figure 4-4) 77
- 79
- 80
- CAN0007A 82
- 114074 Rev. A 4-15 83
- 4-16 114074 Rev. A 84
- 114074 Rev. A 4-17 85
- 4-18 114074 Rev. A 86
- 1. Click on Client I/F 87
- Chapter 5 91
- Network Boot Client 91
- <TFTP host> 92
- (continued) 92
- <TFTP 93
- (continued) 93
- <interface> 94
- <next 94
- <interface> 95
- <IP address> 95
- <subnet mask> 95
- <next hop 95
- 114074 Rev. A 5-8 98
- Chapter 6 99
- 101
- 6-4 114074 Rev. A 102
- 114074 Rev. A 6-5 103
- 6-6 114074 Rev. A 104
- About the N11 DCM 105
- 6-8 114074 Rev. A 106
- Ethernet Statistics Group 107
- Host Group 107
- HostTopN Group 108
- Matrix Group 108
- Filter Group 108
- Packet Capture Group 108
- Enabling the DCM 109
- 111
- 112
- 112
- 113
- 113
- 114
- 114074 Rev. A 6-19 117
- 2. Click on OK 119
- RMON Implementation Notes 121
- RMON Interoperability Issues 121
- 6-24 114074 Rev. A 122
- 114074 Rev. A 6-25 123
- 6-26 114074 Rev. A 124
- 114074 Rev. A 6-27 125
- 6-28 114074 Rev. A 126
- 114074 Rev. A 6-29 127
- Appendix A 129
- Router Fails to Netboot 131
- 114074 Rev. A A-5 133
- <connector> 135
- 114074 Rev. A A-9 137
- Displaying Parameter Settings 138
- 114074 Rev. A A-11 139
- Debugging the BOOTP Server 140
- Table A-1. BOOTP Messages 141
- <IP_address> 143
- Upgrading the Software Image 145
- Restoring a Local File System 145
- Appendix B 147
- Global Information Worksheet 149
- Router Protocol Worksheets 151
- OSPF Worksheet 152
- Wide-Area Protocol Worksheets 154
- Frame Relay Worksheet 155
- PPP Standard Worksheet 156
- CAN0008A 160
- Appendix C 161
- Implementation Notes 161
- C-2 114074 Rev. A 162
- Network Configuration Options 163
- Configuring a Single ANH 164
- 114074 Rev. A C-5 165
- Configuring Multiple Hubs 166
- CAN0010A 167
- C-8 114074 Rev. A 168
- CAN0011A 169
- CAN0012A 170
- 114074 Rev. A Index-1 171
- 114074 Rev. A Index-3 173
- 114074 Rev. A Index-5 175
- 114074 Rev. A Index-7 177
Relacionado con productos y manuales para Software Avaya Connecting BayStack AN and ANH Platforms to a Network
Software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manual de usuario
(148 paginas)
(148 paginas)
Software Avaya Configuring Traffic Filters and Protocol Prioritization Manual de usuario
(162 paginas)
(162 paginas)
Software Avaya Nortel Business Communications Manager 450 1.0 Administration and Security Manual de usuario
(200 paginas)
(200 paginas)
Software Avaya BCM 4.0 Manual de usuario
(398 paginas)
(398 paginas)
Software Avaya Business Communications Manager - Multimedia Contact Center Manual de usuario
(38 paginas)
(38 paginas)
Software Avaya Media Processing Server Series Alarm Reference Manual (Software Release 2.1) Manual de usuario
(452 paginas)
(452 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales