Avaya BCM 2.0 IP Telephony Manual de usuario Pagina 67
- Pagina / 76
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuration 67
P0911590 Issue 02 Enterprise Edge 2.0 IP Telephony Configuration Guide
The Modify Entry option allows the administrator to change the information in an
entry. The administrator highlights an entry on the existing table and selects the
Modify Entry option. A dialog box allows changes to entry information. A default
button restores the information to the settings shown in the table.
Core telephony services configuration
Launch the Enterprise Edge Unified Manager and configure the following:
1. Put the IP trunks into a line pool. IP Telephony ports are IP trunks. Start with
Line 01, to a maximum of Line 08 (depending on the keycode entered).
2. Configure a route which uses the line pool linked with the IP trunks. For IP
trunks, do not add or absorb because the IP telephony gateway receives the
dialed digits as dialed.
3. Enter a destination code which uses the route configured above. Ensure the
destination code is the identical to the destination digits in the Remote
Gateway Configuration. See the Remote Gateway Configuration section on
page 65.
The above procedure ensures Direct Outward Dial (DOD) calls go to a remote
gateway.
To receive Direct Inward Dial (DID) calls, configure DID lines, also called target
lines, on the core telephony services. The full dialed number passes from the
originating to the destination gateway during call setup. The destination gateway
processes the dialed number to determine which DID line can terminate the call.
For private networking, the call terminates at a terminal at the destination gateway.
Configure target lines which match to the dialed digits to complete private
networking. For a description of target lines and DID, see the Enterprise Edge
Programming Operations Guide.
For toll bypass, the DID calls can terminate on an outgoing PSTN trunk. To do this,
configure additional destination codes. These destination codes point to line pools
which contain PSTN trunks. For information about line pools, see the Enterprise
Edge Programming Operations Guide.
Configuration of fallback to conventional circuit-switched facilities
If the measured Mean Opinion Score (MOS) for all codecs is below the configured
threshold for any monitored gateway, the Fallback to Conventional Circuit-
switched services activates. This feature reroutes calls to different trunks such as the
Public Switched Telephone Network (PSTN) until the network QoS improves.
When the QoS meets or exceeds the threshold, calls route over the IP network.
- Enterprise Edge 2.0 1
- IP Telephony 1
- Configuration Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Overview 7
- About this document 8
- System Functions 8
- Dialing plan support 9
- Network Quality of Service 10
- Overview 11 11
- Network Performance Utilities 12
- Silence compression 13
- Echo cancellation 13
- Fax calls 14
- Alarm Notification 14
- Jitter buffer 14
- Engineering guidelines 15
- 16 Engineering guidelines 16
- Engineering guidelines 17 17
- Multiple network interfaces 18
- Method 1 19
- Method 2 19
- LAN engineering 20
- WAN engineering 22
- Link utilization 23
- 24 Engineering guidelines 24
- Setting QoS 26
- Measuring Intranet QoS 27
- Recording routes 28
- Adjusting ping measurements 29
- Measurement procedure 29
- Further network analysis 31
- Reduce link delay 32
- Reducing hop count 32
- Engineering guidelines 33 33
- Routing issues 34
- Traffic mix 35
- TCP traffic behavior 35
- Implementing the network 36
- IP telephony settings 37
- Engineering guidelines 39 39
- Figure 5 Silence compression 39
- Fallback threshold 42
- Dialing plan 43
- 44 Engineering guidelines 44
- Engineering guidelines 47 47
- 48 Engineering guidelines 48
- Figure 8 Toll bypass 48
- Setting 49
- 52 Engineering guidelines 52
- Intranet QoS monitoring 53
- User feedback 54
- Engineering checklist 55
- 56 Engineering checklist 56
- Installation 57
- Configuring a remote gateway 58
- Installation 59 59
- 60 Installation 60
- Configuration 61
- User Interface Overview 62
- Local Gateway Configuration 63
- Remote Gateway Configuration 65
- Configuration 67 67
- 68 Configuration 68
- Maintenance 69
- 70 Maintenance 70
- Interoperability 71
- No feedback busy station 72
- Glossary 73
- 76 Index 76
- Voice Jitter Buffer 76
Relacionado con productos y manuales para Gateways / Controladores Avaya BCM 2.0 IP Telephony
(442 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.202 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales