Avaya Configuring PPP Services Manual de usuario Pagina 42
- Pagina / 118
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring PPP Services
2-16 114068 Rev. A
The multilink feature uses the automatically enabled functions of protocol
prioritization, but only for interrupt queuing. You cannot specify either traffic
filters or priorities. Multilink assigns the highest (that is, interrupt-level) priority
to link control packets, treating all other traffic as normal priority. This gives PPP
control messages precedence over other types of data while preserving the packet
sequencing.
Differences between Multiline and Multilink
Both multiline and multilink use circuits consisting of one or more data paths
between two peer routers. Each has its special characteristics and advantages,
described in the following paragraphs and summarized in
Table 2-3.
Table 2-3. Comparing Multiline and Multilink
Feature Multiline Multilink
Advantages • Fault tolerance
• Bandwidth availability
• Fault tolerance
• Bandwidth availability
• Uses all lines in the bundle for
greatest speed and efficiency
Number of
physical lines/
circuit
• Up to 31 concurrent data
paths/group
• Data paths can either be
physical or logical lines
(multiple independent data
paths running over a single
physical interface)
Up to 30 lines/bundle, depending
on platform constraints, total
bundle speed, variance in
member links speeds, and traffic
characteristics. Please consult the
Bay Networks Technical
Response Center in your area for
design guidelines.
Grouped/bundled
data paths
The data paths that together
make up a multiline circuit must
share the same speed, MTU,
and encapsulation method
Lines in a bundle can have
different speeds
Line types Can use leased lines Can use leased as well as
switched lines
Protocol
prioritization
• Automatically enabled
• User can specify protocol
priority and/or traffic filters
• Automatically enabled
• Not user configurable
• Automatically assigns highest
(interrupt) priority to LCP
packets and assigns all others
normal priority
(continued)
- Configuring PPP 1
- Services 1
- Bay Networks Software License 3
- Contents 5
- 114068 Rev. A vii 7
- 114068 Rev. A ix 9
- 114068 Rev. A xi 11
- About This Guide 13
- Before You Begin 14
- Conventions 14
- Acronyms 15
- 114068 Rev. A xvii 17
- Bay Networks Customer Service 18
- World Wide Web 19
- Customer Service FTP 19
- Support Source CD 20
- CompuServe 20
- InfoFACTS 21
- How to Get Help 21
- Chapter 1 23
- Starting PPP 23
- PPP Tasks 24
- Where to Go Next 25
- Router Router 27
- Synchronous Line 27
- PPP0001A 27
- 2-2 114068 Rev. A 28
- Routing over a PPP Link 29
- Initializing a PPP Interface 30
- PPP Concepts 31
- Router A Router B 32
- PPP0002A 32
- Datagram Encapsulation 34
- PPP Dial Services Support 35
- PPP Multiline 36
- PPP Multilink 37
- PPP0005A 38
- Circuit 38
- Bundle with 2 Links 38
- Balancing Traffic Loads 40
- Using Multilink Fragmentation 40
- PPP0004A 44
- PPP Data Compression 45
- 2-20 114068 Rev. A 46
- PPP Line Parameters 48
- Detecting Loopback Conditions 49
- PPP Interoperability 50
- Chapter 3 53
- Customizing PPP 53
- Setting Up Remote Addresses 54
- Configuring AppleTalk 56
- Enabling Bridging 57
- Enabling Ethernet Bridging 57
- Enabling FDDI Bridging 57
- Enabling Token Ring Bridging 57
- 3-6 114068 Rev. A 58
- 3-8 114068 Rev. A 60
- Customizing PPP Lines 61
- Editing PPP Line Parameters 62
- Setting the Restart Timer 63
- 3-12 114068 Rev. A 64
- 3-14 114068 Rev. A 66
- Customizing PAP 67
- 3-16 114068 Rev. A 68
- Customizing CHAP 69
- 3-18 114068 Rev. A 70
- 3-20 114068 Rev. A 72
- 3-22 114068 Rev. A 74
- Disabling Loopback Checking 76
- Deleting PPP 76
- Appendix A 79
- A-8 114068 Rev. A 86
- 89
- A-12 114068 Rev. A 90
- A-16 114068 Rev. A 94
- 95
- A-18 114068 Rev. A 96
- 98
- Configuring PPP Services 100
- A-22 114068 Rev. A 100
- PPP Parameters 101
- 102
- (continued) 105
- (continued) 106
- 114068 Rev. A Index-1 111
- 114068 Rev. A 112
- 114068 Rev. A Index-3 113
- 114068 Rev. A Index-5 115
- 114068 Rev. A Index-7 117
Relacionado con productos y manuales para Redes Avaya Configuring PPP Services
Redes Avaya BCM50/450 Guía de configuración
(38 paginas)
(38 paginas)
Redes Avaya Configuring RADIUS Manual de usuario
(116 paginas)
(116 paginas)
Redes Avaya Configuring MPOA Services Manual de usuario
(148 paginas)
(148 paginas)
Redes Avaya BCM 2.5 Guía de usuario
(50 paginas)
(50 paginas)
Redes Avaya Glossary of Media Processing Server Series Terminology (Software Release 2.1) Manual de usuario
(124 paginas)
(124 paginas)
Redes Avaya BayRS Version 15.2.0.0 aviso
(68 paginas)
(68 paginas)
Redes Avaya Configuring DLSw Services Manual de usuario
(204 paginas)
(204 paginas)
Redes Avaya BCM200/400 Manual de instalación
(386 paginas)
(386 paginas)
Redes Avaya X.25 Manual de usuario
(198 paginas)
(198 paginas)
Redes Avaya Configuring OSI Services Manual de usuario
(148 paginas)
(148 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales