Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services Manual de usuario Pagina 155
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Customizing RIP Services
308627-14.20 Rev 00
5-11
Sending Triggered Updates
RIP generates full routing updates at regular intervals. You can also configure RIP
to generate a triggered update on a specified interface each time it recalculates a
route’s metric. A triggered update contains only the routes that have changed.
(RIP also sends full updates at regular intervals on interfaces configured for
triggered updating.)
By default, triggered updates are disabled on all interfaces configured for RIP.
You can use the BCC or Site Manager to enable and disable triggered updates on
this interface.
Using the BCC
To enable or disable triggered updates, go to a RIP interface prompt (for example,
box; eth 2/2; ip/2.2.2.2/255.255.0.0; rip
) and enter:
triggered-updates
<state>
state
is one of the following:
enabled
disabled
(default)
For example, the following command enables triggered updates on IP interface
2.2.2.2:
rip/2.2.2.2#
triggered-updates enabled
rip/2.2.2.2#
5. Set the Poisoned Reverse parameter.
Click on Help or see the parameter
description on page A-64.
6. Click on Apply, and then click on Done. You return to the Configuration Manager
window.
Site Manager Procedure
(continued)
You do this System responds
- Configuring IP, ARP, RARP 1
- RIP, and OSPF Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308627-14.20 Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 33
- OSPF Neighbors 37
- Neighbor Adjacencies 37
- Designated Routers 38
- AS External Routes 38
- OSPF Areas 39
- OSPF Router Types 41
- OSPF Implementation Notes 41
- Router Discovery Protocol 42
- Route Preferences 43
- Route Weights 44
- Figure 1-7. IP Routing Table 46
- IP Traffic Filters 50
- Chapter 2 51
- Starting IP Services 51
- Starting RIP 53
- Starting OSPF 54
- Starting Router Discovery 54
- Adding RIP to an IP Interface 57
- Starting RARP 59
- Chapter 3 61
- Setting the ICMP Error Limit 75
- Caution: 81
- Customizing an IP Interface 84
- Specifying a MAC Address 97
- IP0012A 99
- Using the BCC 100
- Using Site Manager 100
- Configuring an SMDS Address 102
- (continued) 103
- Deleting IP from an Interface 106
- Defining a Static Route 117
- (continued) 119
- Defining a Default Route 121
- Customizing Router Discovery 122
- Choosing a Broadcast Type 124
- Chapter 4 129
- Customizing ARP 130
- Customizing Global ARP 131
- Figure 4-1. Proxy ARP Example 137
- Customizing RARP 141
- Deleting RARP Globally 144
- Chapter 5 145
- Customizing RIP Services 145
- Setting the RIP Diameter 146
- Customizing a RIP Interface 147
- Selecting the RIP Version 148
- ) and enter: 149
- Specifying the Update Mode 153
- Sending Triggered Updates 155
- Receiving RIP Updates 158
- Listening for a Default Route 161
- Defining a RIP Accept Policy 170
- Chapter 6 185
- Customizing OSPF Services 185
- Supplying an OSPF Router ID 188
- Figure 6-1. OSPF ASE Routes 193
- Setting the Holddown Timer 198
- <value> 199
- <seconds> 199
- Configuring Message Logging 200
- Changing the Area ID 205
- Specifying the Interface Type 206
- Estimating the Transit Delay 210
- Setting the Hello Interval 212
- Setting the Dead Interval 214
- Specifying the Metric Cost 217
- Specifying the MTU Size 219
- Examples 223
- Configuring Areas 226
- Configuring Authentication 229
- Configuring a Summary Route 231
- Configuring a Stub Area 233
- Transit area 244
- Policies 257
- Appendix A 263
- Site Manager Parameters 263
- IP Parameters 264
- IP Interface Parameters 266
- IP Global Parameters 280
- Static Route Parameters 289
- Adjacent Host Parameters 292
- Router Discovery Parameters 295
- RARP Parameters 297
- OSPF Parameters 298
- OSPF Global Parameters 299
- OSPF Interface Parameters 303
- OSPF Area Parameters 311
- Area Range Parameters 315
- OSPF NSSA Range Parameters 318
- RIP Parameters 324
- Manager online Help 331
- RIP Accept Policy Parameters 335
- OSPF Accept Policy Parameters 337
- Appendix B 353
- RIP Import Filters 354
- RIP Export Filters 357
- OSPF Import Filters 360
- OSPF Export Filters 363
- Appendix C 367
- Route Weight Worksheet 367
- Appendix D 371
- IP/OSPF Configuration Example 371
- Manager and the BCC 374
Relacionado con productos y manuales para Software Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services
Software Avaya BayRs Version 12.20 Manual de usuario
(218 paginas)
(218 paginas)
Software Avaya PeriReporter Business Communications Manager Release 6.0 Manual de usuario
(133 paginas)
(133 paginas)
Software Avaya CS1000 Manual de usuario
(180 paginas)
(180 paginas)
Software Avaya Digital Enchanced Cordless Telecommuncations SIP DECT Fundamentals Manual de usuario
(254 paginas)
(254 paginas)
Software Avaya Connecting BayStack AN and ANH Platforms to a Network Manual de usuario
(178 paginas)
(178 paginas)
Software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manual de usuario
(148 paginas)
(148 paginas)
Software Avaya Configuring Traffic Filters and Protocol Prioritization Manual de usuario
(162 paginas)
(162 paginas)
Software Avaya Nortel Business Communications Manager 450 1.0 Administration and Security Manual de usuario
(200 paginas)
(200 paginas)
Software Avaya BCM 4.0 Manual de usuario
(398 paginas)
(398 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales