Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manual de usuario Pagina 113
- Pagina / 130
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring RARP Services
114070 Rev. A 5-3
When you enable RARP services, you are required to configure only a few
parameters. The Configuration Manager supplies default values for the remaining
parameters.
This section assumes you have read Configuring Routers or Configuring
Customer Access (BNX Software), depending on the type of installed software,
and that you have
1. Opened a configuration file
2. Specified router hardware if this is a local mode configuration file
3. Selected either the link or net module connector on which you are enabling IP
services, or configured a WAN circuit if this connector requires one
Enabling RARP on an Interface
When you select either a link or net module connector, or when you finish
configuring a WAN circuit, the Select Protocols window appears (r
efer to
Figure 1-1).
To enable RARP on an interface:
1. Select Reverse ARP from the Select Protocols menu.
When you select RARP, you automatically select IP.
2. Click on OK.
The IP Configuration window appears (r
efer to Figure 1-2).
3. Edit the parameters on the screen.
Refer to “Ena
bling IP on an Interface” in Chapter 1 for guidelines.
4. Edit or accept the default values for the remaining IP interface
parameters, as follows:
• To accept the default values, click on OK.
Site Manager displays the Configuration Manager window. You can now
customize RARP parameters for the IP interface (r
efer to “Editing RARP
Parameters”).
Note: The window displays only those protocols that the circuit type supports.
- Configuring SNMP 1
- RMON, BOOTP, DHCP 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- 114070 Rev. A 10
- About This Guide 15
- Software Suites 16
- Before You Begin 16
- Conventions 17
- Acronyms 18
- World Wide Web 21
- Customer Service FTP 21
- Support Source CD 22
- CompuServe 22
- InfoFACTS 23
- How to Get Help 23
- Configuring 25
- SNMP Implementation Notes 26
- Threshold Example 27
- 1-4 114070 Rev. A 28
- Configuring SNMP Services 29
- Enabling SNMP Services 30
- To enable IP on an interface: 31
- Click on OK 31
- 1-8 114070 Rev. A 32
- Editing SNMP Parameters 34
- 114070 Rev. A 1-11 35
- Adding an SNMP Community 38
- 114070 Rev. A 1-15 39
- 40
- Adding a Manager 41
- Editing a Manager 43
- 44
- Editing Threshold Parameters 45
- 1-22 114070 Rev. A 46
- Configuring a Threshold 47
- 49
- 51
- 52
- 53
- Editing Trap Parameters 54
- Configuring Exceptions 55
- Deleting Exceptions 58
- Chapter 2 59
- Using RMON Services 59
- 2-2 114070 Rev. A 60
- The RMON Architecture 61
- The RMON Groups 62
- Ethernet Statistics Group 63
- History Control Group 63
- Ethernet History Group 63
- Host Group 64
- HostTopN Group 64
- Matrix Group 64
- Filter Group 64
- RMON Interoperability Issues 65
- RMON Memory Use 66
- 2-10 114070 Rev. A 68
- 2-12 114070 Rev. A 70
- Enabling the DCM 71
- 2-14 114070 Rev. A 72
- Disabling the Ethernet DCM 75
- Activating the Ethernet DCM 75
- Booting the Ethernet DCM 76
- 114070 Rev. A 2-19 77
- Chapter 3 79
- Configuring BOOTP Services 79
- 3-2 114070 Rev. A 80
- Configuring BOOTP Services 81
- 3-4 114070 Rev. A 82
- 3-6 114070 Rev. A 84
- Enabling BOOTP Services 85
- Editing BOOTP Parameters 87
- 114070 Rev. A 3-13 91
- 3-16 114070 Rev. A 94
- 2. Click on Delete 94
- 114070 Rev. A 3-17 95
- 3-18 114070 Rev. A 96
- 4. Click on OK 96
- 114070 Rev. A 3-19 97
- 100
- Deleting BOOTP Globally 101
- Chapter 4 103
- Configuring DHCP Services 103
- 4-2 114070 Rev. A 104
- Configuring DHCP Services 105
- 4-4 114070 Rev. A 106
- Implementation Notes 108
- Enabling DHCP Services 108
- Enabling DHCP on an Interface 108
- Editing DHCP Parameters 109
- Deleting DHCP Globally 110
- Chapter 5 111
- Configuring RARP Services 111
- Enabling RARP Services 112
- Enabling RARP on an Interface 113
- Editing RARP Parameters 114
- 114070 Rev. A 5-5 115
- 116
- 114070 Rev. A 5-7 117
- Disabling RARP Globally 118
- Deleting RARP Globally 119
- Appendix A 121
- Default Parameter Settings 121
- A-2 114070 Rev. A 122
- BOOTP and DHCP Parameters 123
- RARP Parameters 124
- 114070 Rev. A Index-1 125
- 114070 Rev. A Index-3 127
- 114070 Rev. A Index-5 129
Relacionado con productos y manuales para Manuales de software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services
(76 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales