Avaya Configuring IP, ARP, RIP, and OSPF Services Manual de usuario Pagina 209
- Pagina / 374
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Customizing OSPF Services
308627-14.00 Rev 00
6-31
For example, the following command sets the poll interval to 90 seconds on IP
interface 2.2.2.2:
ospf/2.2.2.2# poll-interval 90
ospf/2.2.2.2#
Using Site Manager
To specify a poll interval, complete the following tasks:
Specifying the Metric Cost
For OSPF, the best path is the one that offers the least-cost metric.
You must configure cost metrics if you want to specify a preferred path. Allow the
preferred path to retain the default cost metric value of 1, and then assign
higher-cost metric values to the less-preferred paths.
Figure 6-3
illustrates the benefit of using configurable cost metrics. Assigning the
56 Kb line a cost metric value of 10 forces OSPF to choose the faster T1 line path
as the best path, despite the extra hop, when transmitting a packet from host A to
host B.
Site Manager Procedure
You do this System responds
1. In the Configuration Manager window,
choose
Protocols
.
The Protocols menu opens.
2. Choose
IP
. The IP menu opens.
3. Choose
OSPF/MOSPF
. The OSPF/MOSPF menu opens.
4. Choose
Interfaces
. The OSPF Interfaces window opens.
5. Click on the OSPF interface that you want
to edit.
The parameter values for that interface
appear in the OSPF Interfaces window.
6. Set the
Poll Interval
parameter. Click on
Help
or see the parameter description on
page A-46.
7. Click on
Apply
, and then click on
Done
. You return to the Configuration Manager
window.
- Configuring IP, ARP, RARP 1
- RIP, and OSPF Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308627-14.00 Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 32
- OSPF Neighbors 36
- Neighbor Adjacencies 36
- Designated Routers 37
- OSPF Areas 38
- OSPF Router Types 40
- AS External Routes 40
- OSPF Implementation Notes 41
- Router Discovery Protocol 42
- Route Preferences 42
- Route Weights 43
- Figure 1-7. IP Routing Table 45
- IP Traffic Filters 48
- Chapter 2 49
- Starting IP Services 49
- Starting RIP 51
- Starting OSPF 52
- Starting Router Discovery 52
- Adding RIP to an IP Interface 55
- Starting RARP 57
- Chapter 3 63
- Caution: 80
- Customizing an IP Interface 82
- IP0012A 97
- Configuring an SMDS Address 100
- (continued) 101
- Using the BCC 103
- Using Site Manager 104
- Deleting IP from an Interface 107
- Defining a Static Route 111
- 3.2.4.5/255.255.0.0: 113
- Choosing a Broadcast Type 118
- Chapter 4 123
- Customizing ARP 124
- Customizing Global ARP 125
- (continued) 129
- Figure 4-1. Proxy ARP Example 130
- Customizing RARP 134
- Deleting RARP Globally 137
- Chapter 5 139
- Customizing RIP Services 139
- Setting the RIP Diameter 140
- Customizing a RIP Interface 141
- Selecting the RIP Version 142
- Specifying the Update Mode 147
- Sending Triggered Updates 149
- Listening for a Default Route 155
- Defining a RIP Accept Policy 163
- Chapter 6 179
- Customizing OSPF Services 179
- Supplying an OSPF Router ID 182
- Figure 6-1. OSPF ASE Routes 187
- Setting the Holddown Timer 192
- Configuring Message Logging 193
- Configuring an Area ID 198
- Specifying the Interface Type 199
- Estimating the Transit Delay 202
- Setting the Hello Interval 205
- Setting the Dead Interval 207
- Specifying the Metric Cost 209
- Table 6-6. Cost Settings 210
- Specifying the MTU Size 212
- Defining an Area 218
- Configuring Authentication 221
- Configuring a Summary Route 222
- Configuring a Stub Area 224
- 0.0.0.1: 229
- Policies 247
- Appendix A 251
- Site Manager Parameters 251
- IP Parameters 252
- IP Interface Parameters 254
- IP Global Parameters 269
- Static Route Parameters 276
- Adjacent Host Parameters 280
- Router Discovery Parameters 283
- RARP Parameters 285
- OSPF Parameters 287
- OSPF Interface Parameters 292
- OSPF Area Parameters 301
- Area Range Parameters 305
- OSPF NSSA Range Parameters 308
- RIP Parameters 314
- Appendix B 321
- Routing Policy Parameters 321
- RIP Accept Policy Parameters 325
- OSPF Accept Policy Parameters 326
- Appendix C 343
- RIP Export Filters 347
- OSPF Import Filters 350
- OSPF Export Filters 351
- Appendix D 355
- Route Weight Worksheet 355
- Appendix E 359
- IP/OSPF Configuration Example 359
- 10.1.1.0 360
- 255.255.255.0 (RIP Only) 360
Relacionado con productos y manuales para Redes Avaya Configuring IP, ARP, RIP, and OSPF Services
Redes Avaya BCM450 Manual de usuario
(22 paginas)
(22 paginas)
Redes Avaya BSGX4e Guía de usuario
(206 paginas)
(206 paginas)
Redes Avaya Event Messages for Routers Manual de usuario
(838 paginas)
(838 paginas)
Redes Avaya a WAN Adapter Module in a BayStack ARN Router (114204 Rev. A) Manual de usuario
(34 paginas)
(34 paginas)
Redes Avaya Configuring IPX Services Manual de usuario
(254 paginas)
(254 paginas)
Redes Avaya Integrated Management Release 2.2 Network Management Console Guía de usuario
(154 paginas)
(154 paginas)
Redes Avaya VLANs BCM Rls 6.0 Manual de usuario
(22 paginas)
(22 paginas)
Redes Avaya 1100-Series Manual de usuario
(48 paginas)
(48 paginas)
Redes Avaya BCM50 2.0 Guía de usuario
(26 paginas)
(26 paginas)
Redes Avaya 0604DAX aviso
(20 paginas)
(20 paginas)
Redes Avaya 2050 IP Softphone Manual de usuario
(26 paginas)
(26 paginas)
Redes Avaya R5.0: Guía de configuración
(20 paginas)
(20 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales