Avaya Digital Enchanced Cordless Telecommuncations SIP DECT Fundamentals Manual de usuario Pagina 92
- Pagina / 254
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
92 Site planning
Procedure 26
Determining cell reengineering
Step Action
1 Locate the estimate for users in the first cell.
In the example shown in Table 16 "Example of a completed
estimate table" (page 91), the handset estimate is 11.6.
2 Determine the telephone types in the first cell.
In the example shown in Table 16 "Example of a completed
estimate table" (page 91), the telephone type is H&W.
3 Locate the telephone type column in Table 16 "Example of a
completed estimate table" (page 91).
In the example H&W is the users with both a handset and a
wired telephone.
4 Find the handset estimate range in Table 18 "Cell reengineering"
(page 91).
In the example, 11.6 falls within the From 0 up to 20 category.
5 Determine if a cell requires division or uses a 12-channel
basestation.
In the example From 0 up to 20, division is not required.
6 Repeat the preceding steps to determine the required number of
cells that need subdivision, except for telephone types M. For M
see “A mix of users with and without wired telephones in a cell”
(page 93).
7 Transfer the results into the provisioning records.
--End--
Cell division requirements in special cases
This section describes how to determine cell division in the following
special cases.
• Where no office information is available.
• Where there is a mix of handset users with and without wired
telephones.
No office information
If the location of the offices of users is not known, calculate the estimated
number of handsets for each cell using this formula.
Nortel Communication Server 1000
SIP DECT Fundamentals
NN43120-123 01.07
6 January 2009
Copyright © 2008-2009 Nortel Networks
.
- SIP DECT Fundamentals 1
- Contents 3
- Hardware installation 99 4
- Software requirements 103 4
- System configuration 135 4
- System administration 185 5
- System maintenance 215 5
- Location builder tool 239 6
- New in this release 7
- 8 New in this release 8
- Product overview 9
- • Call Server, Release 5.5 10
- Overview of SIP DECT 11 11
- Figure 1 11
- SIP DECT configuration 11
- 12 Product overview 12
- Figure 2 12
- — Disable IGMP Snooping 13
- 14 Product overview 14
- Overview of SIP DECT 15 15
- DECT handset features 16
- SIP DECT capacity limitations 17
- 18 Product overview 18
- Site planning 19
- • elevators 20
- • stairwells 20
- • washrooms 20
- • outdoor areas 20
- Number of handset users 21
- Customer review 21
- A normal site survey 21
- The facts for Able-Studio 22
- Gather survey items 22
- Identify site contacts 23
- Obtain site plans 23
- Gather building information 24
- Identify existing cabling 25
- Assess radio coverage 25
- Profile handset use 26
- Radio synchronization 27
- Synchronization hierarchy 29
- IP network configuration 31
- Ethernet requirements 31
- Fixed IP network addresses 32
- Dynamic IP network addresses 33
- Multicast addresses 33
- • stairwell 34
- • second floor plan 34
- 36 Site planning 36
- Figure 8 36
- Cell centers 36
- Figure 9 37
- Determine cell boundaries 38
- Deployment illustrations 42
- Figure 15 43
- Figure 16 43
- 44 Site planning 44
- Figure 17 44
- Figure 18 44
- Example of a cell center 44
- Figure 19 45
- Figure 20 45
- 46 Site planning 46
- Figure 21 46
- Figure 22 46
- Figure 23 47
- Figure 24 47
- 48 Site planning 48
- Figure 25 48
- Figure 26 48
- Figure 27 49
- Figure 28 49
- Deployment terms 50
- Coverage terms 51
- Deployment tool 52
- Deployment tool 53 53
- Figure 32 53
- 54 Site planning 54
- Figure 33 54
- Assembled deployment tool 54
- 56 Site planning 56
- Figure 35 56
- Procedure 8 56
- Step Action 58
- 1 Set up the tripod 58
- Deployment tool 59 59
- 60 Site planning 60
- Figure 38 60
- Procedure 10 60
- How the deployment tool works 61
- Using the deployment tool 62
- Handset tones interpretation 63
- Rules for outdoor deployment 63
- DECT Deployment Kit 2 64
- DECT Deployment Kit 2 65 65
- 66 Site planning 66
- Figure 41 66
- DAP deployment 67
- 68 Site planning 68
- DAP deployment 69 69
- 70 Site planning 70
- Procedure 13 71
- Single floor deployment 72
- Single-cell deployment 73
- 74 Site planning 74
- Double cell deployment 75
- Multi cell deployment 76
- Figure 45 77
- Multi-cell distance 77
- Procedure 16 77
- Multi-cell deployment 77
- Multiple floor deployment 78
- Assess floor layout 79
- • “Atriums ” (page 80) 80
- 82 Site planning 82
- Traffic volume 83
- 84 Site planning 84
- Creating an estimate table 85
- No office information 92
- Subdivide a cell 95
- 96 Site planning 96
- Procedure 28 96
- Deployment review 97
- 98 Site planning 98
- Figure 51 98
- Hardware installation 99
- NN43120-123 01.07 100
- 6 January 2009 100
- DECT Access Points 101 101
- 102 Hardware installation 102
- Software requirements 103
- 104 Software requirements 104
- • 30160 – CDA services 105
- 106 Software requirements 106
- Procedure 31 106
- DAP controller software 107 107
- Procedure 32 107
- 108 Software requirements 108
- Procedure 33 108
- Restarting IIS 108
- DAP controller software 109 109
- Procedure 34 109
- 110 Software requirements 110
- Procedure 35 110
- DHCP and TFTP servers 111
- • IP Address 112
- • Default Gateway IP address 112
- DAP controller software 113 113
- Procedure 38 113
- 114 Software requirements 114
- Procedure 39 114
- DAP controller software 115 115
- 116 Software requirements 116
- DAP controller software 117 117
- 13 Click Next 118
- DAP controller software 119 119
- 120 Software requirements 120
- TFTP server 121
- 122 Software requirements 122
- Procedure 40 122
- Installing the TFTP server 122
- DAP controller software 123 123
- Procedure 41 123
- Starting the TFTP server 123
- ATTENTION 124
- Built-in DHCP server 124
- DAP controller software 125 125
- Procedure 42 125
- Network Settings Window 125
- Built-in TFTP server 126
- 128 Software requirements 128
- DAP controller software 129 129
- Procedure 44 129
- DAP Controller 130
- Prerequisites 130
- DAP controller software 131 131
- 132 Software requirements 132
- 13 Click Finish 133
- 134 Software requirements 134
- System configuration 135
- 136 System configuration 136
- Procedure 46 137
- 138 System configuration 138
- Procedure 47 138
- Procedure 48 139
- Configuring IP Settings 139
- 142 System configuration 142
- Procedure 52 143
- Configuring DECT Settings 143
- • Performance Settings 146
- • Advanced Email Settings 146
- 148 System configuration 148
- Procedure 54 148
- Procedure 55 149
- Saving the system 149
- DAP manager configuration 150
- Rebooting DECT Access Points 150
- Adding number range 151
- Subscribing a DECT handset 152
- 154 System configuration 154
- Creating a new customer 155
- Zone configuration 155
- Adding a D-Channel 156
- Adding a route 156
- Adding trunks 157
- Configuring network access 158
- Creating ESN control block 158
- Adding route list block 159
- Adding location code (UDP) 160
- Procedure 71 161
- Configuring SIP properties 162
- NRS configuration 163
- 164 System configuration 164
- Procedure 74 164
- Creating service domain 165
- Adding the UDP domain 165
- Adding the CDP domain 165
- Procedure 79 167
- 168 System configuration 168
- Procedure 80 168
- Procedure 81 169
- Saving changes 170
- Call server configuration 170
- • aaa = MCN, MCR, SCN, or SCR 171
- • yyyy = primary DN 172
- • 192.168.1.0/24 174
- • 192.168.4.0/24 174
- • 192.168.5.0/24 174
- 176 System configuration 176
- Procedure 84 176
- Procedure 85 177
- Procedure 86 177
- 178 System configuration 178
- Procedure 87 178
- Procedure 88 178
- • Codes on system 1 179
- Personal Call Assistant 180
- 184 System configuration 184
- System administration 185
- 186 System administration 186
- Subscription management 187
- Edit a subscription RPN 188
- Disable a subscription 189
- Remove a subscription 190
- Delete a number 190
- Use the DNR filter 191
- • Status 192
- • Presence status 193
- • Registration status 193
- • Handset Type and SW Version 193
- DAP management 194
- Reboot a DAP 195
- Reboot all DAPs 195
- Add a DN range 196
- 198 System administration 198
- Procedure 101 198
- Restoring a subscription 198
- Export subscriptions 199
- 200 System administration 200
- Import subscriptions 201
- DAP reboot histor y 202
- System archive 202
- System archive 203 203
- Handset firmware update 204
- • Retry interval, in minutes 205
- 206 System administration 206
- Handset firmware update 207 207
- • Remove Ready Handsets 208
- Central directory access tool 208
- Supported database types 209
- Installation 210
- • Nortel AccessService 212
- • Nortel DirectoryService 212
- Procedure 109 213
- Configuring IP DECT 213
- 214 System administration 214
- System maintenance 215
- DAP firmware update 216
- 218 System maintenance 218
- Replacing a DAP 218
- Procedure 111 218
- 220 System maintenance 220
- • Tree view 221
- • Visibility Information 221
- Building Information 222
- DAP Information 222
- • Red = root level 224
- • Green = first level 224
- • Yellow = second level 224
- Procedure 112 225
- Tracking a por table device 225
- Export a system 228
- Import a system 229
- 230 System maintenance 230
- Procedure 116 230
- Procedure 117 231
- If DAP is not working 232
- Troubleshooting 233 233
- 234 System maintenance 234
- Troubleshooting 235 235
- If you have problems 236
- • Signaling server: 236
- • Call server: 236
- • Number of DAPs: 236
- IP addresses 237
- Software version 237
- Configuration 237
- Numbering plan 237
- Network packet capture traces 238
- Appendix 239
- Location builder tool 239
- 240 Location builder tool 240
- Create a location file 241
- 242 Location builder tool 242
- • Add lines in freehand mode: 243
- 244 Location builder tool 244
- Maintenance 246
- 248 Location builder tool 248
Relacionado con productos y manuales para Software Avaya Digital Enchanced Cordless Telecommuncations SIP DECT Fundamentals
Software Avaya Connecting BayStack AN and ANH Platforms to a Network Manual de usuario
(178 paginas)
(178 paginas)
Software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manual de usuario
(148 paginas)
(148 paginas)
Software Avaya Configuring Traffic Filters and Protocol Prioritization Manual de usuario
(162 paginas)
(162 paginas)
Software Avaya Nortel Business Communications Manager 450 1.0 Administration and Security Manual de usuario
(200 paginas)
(200 paginas)
Software Avaya BCM 4.0 Manual de usuario
(398 paginas)
(398 paginas)
Software Avaya Business Communications Manager - Multimedia Contact Center Manual de usuario
(38 paginas)
(38 paginas)
Software Avaya Media Processing Server Series Alarm Reference Manual (Software Release 2.1) Manual de usuario
(452 paginas)
(452 paginas)
MasterCraft manuales
La lista de dispositivos de MasterCraft contiene 28 manuales de usuario y guías para 19 modelos en 14 tipo de dispositivos
Comentarios a estos manuales