Avaya Redundancy BCM Rls 6.0 Manual de usuario

BCM Rls 6.0 Redundancy Task Based Guide

Redundancy 10 NN40011-048 Issue 1.2 BCM450 Rls 6.0 3. Grasp the fan connector at the plug and pull to undo the connection. 4. Next, remove a

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 11 5. The fan is held in place with plastic (two piece) grommets. Simply pull the pin out of t

Redundancy 12 NN40011-048 Issue 1.2 BCM450 Rls 6.0 1. First, grasp the connectors and gently pull to remove the two plugs that connect the power s

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 13 3. Once disconnected, remove all associated retaining screws for the power supply at th

Redundancy 14 NN40011-048 Issue 1.2 BCM450 Rls 6.0 Note: You may require a cutting tool to assist in breaking the connection struts of

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 15 Removing the Front Hard Drive Cover The final preparation task is to remove the Front Hard Drive

Redundancy 16 NN40011-048 Issue 1.2 BCM450 Rls 6.0 Completed Pre-Preparation Check List Upon completion ensure that you have removed:  The curre

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 17 Installing the Redundancy & RAID Kit For the purpose of this guide, we will install the foll

Redundancy 18 NN40011-048 Issue 1.2 BCM450 Rls 6.0 1. Starting with the first unit, ensure the fan label is the right way up (power

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 19 3. Rest the fan faceplate on top of the unit (ensure that the lip of the facepl

Redundancy 2 NN40011-048 Issue 1.2 BCM450 Rls 6.0 Copyright © 2010 Avaya Inc. All Rights Reserved. Notices While reasonable efforts have been made

Redundancy 20 NN40011-048 Issue 1.2 BCM450 Rls 6.0 5. Perform the same procedure for the second fan. 6. Both units should now be fixed to th

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 21 7. Secure the faceplate to the chassis with the fixing screws. 8. Finally, clip both powe

Redundancy 22 NN40011-048 Issue 1.2 BCM450 Rls 6.0 9. Your secondary fan is now installed alongside the original unit. Installing the Redundant

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 23 1. Begin by removing the PSU Status jumper on the Chassis Interface Card. 2.

Redundancy 24 NN40011-048 Issue 1.2 BCM450 Rls 6.0 3. Now that the plate has been removed, you can position the power supply as shown.

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 25 5. Tidy away the cables as necessary, separating the same four leads that will connec

Redundancy 26 NN40011-048 Issue 1.2 BCM450 Rls 6.0 7. Next, reconnect the two leads that will power the MBM’s. 8. Once completed, your connec

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 27 9. You can now reseat the BCM 450 access panel and secure with the retaining screws. 10. The

Redundancy 28 NN40011-048 Issue 1.2 BCM450 Rls 6.0 Installing the Secondary Hard Disk Drive Installing a secondary Hard Disk Drive (for RAID

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 29 3. The secondary Hard Disk Drive is now installed. Replace the front Hard Drive cover and tight

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 3 Downloading documents For the most current versions of documentation, see the Avaya Support. Web

Redundancy 30 NN40011-048 Issue 1.2 BCM450 Rls 6.0 Note: The Disk Mirroring option only becomes visible after RAID keycode entry. 2. If the Ad

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 31 3. Click on the drop down list to change the status, and click OK. 4. Click OK to the secon

Redundancy 32 NN40011-048 Issue 1.2 BCM450 Rls 6.0 LED States HDD-1 LED RAID LED HDD-2 LED Description Green Green Green - BCM completed booting,

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 33 Avaya Documentation Links  Troubleshooting Guide  Installation – System  Maintenance

Redundancy 4 NN40011-048 Issue 1.2 BCM450 Rls 6.0 Table of Contents Redundancy ...

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 5 Redundancy Overview This guide will cover the installation procedures required to instal

Redundancy 6 NN40011-048 Issue 1.2 BCM450 Rls 6.0 RAID Keycode Note: If installing the RAID kit, ensure that the RAID Keycode is showing as act

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 7 Flowchart This flowchart depicts the steps necessary to upgrade a BCM 450 with a redu

Redundancy 8 NN40011-048 Issue 1.2 BCM450 Rls 6.0 Preparing the BCM 450 for Redundancy Kit Installation Before installing a Redundancy kit, th

Redundancy NN40011-048 Issue 1.2 BCM450 Rls 6.0 9 Removing the Fan To install the secondary fan and cover plate, the existing components need to be